1|Page
FANUC CERTIFICATION FINAL EXAM WITH CORRECT
ACTUAL QUESTIONS AND CORRECTLY WELL DEFINED
ANSWERS LATEST 2024 – 2025 ALREADY GRADED A+
Turning the Teach Pendant on: - (answer)Gives motion control solely to the
operator via the teach pendant
What must be accomplished to avoid hard-stops and over travels? - (answer)Set
Axis Limits
SHIFT and the hard key COORD will display the following menu: - (answer)The
"jog" menu
SHIFT and POINT are needed to do what? - (answer)Record the current position
of the robot
In the motion command "J P [2] 100% FINE", If you wanted to change the "FINE"
component to a "CNT100" what buttons would you press? - (answer)Select
component, then press [CHOICE]
To switch manually from one program to another, you have to be in which
screen? - (answer)Select
How many Robot I/O points are standard on a controller? - (answer)16
, 2|Page
Which soft key is pressed to display the current motion instruction defaults from
the EDIT Screen? - (answer)POINT
When creating a program, which hard key should be pressed? - (answer)Select
When using the Prog Adjust utility, which statement is correct? -
(answer)Pressing CLR_ADJ or CLR_ALL will save the enabled data values
Which of the following tasks can be performed from the FILE Menu? -
(answer)Get a default directory of the device
If while jogging the robot, you get an "in singularity" error, What must you do? -
(answer)Joint jog J5 +/- at least 10 degrees
The"Program Header Information" at the DETAIL softkey enables you to modify
the following program information, EXCEPT: - (answer)Active tool frame
What position is the suggested type of motion used to move the robot to a HOME
position? - (answer)Joint
Which softkey allows you to enter additional program instructions into a teach
pendant program? - (answer)[INST]
Which of the following is a type of I/O signal? - (answer)Digital I/O
FANUC CERTIFICATION FINAL EXAM WITH CORRECT
ACTUAL QUESTIONS AND CORRECTLY WELL DEFINED
ANSWERS LATEST 2024 – 2025 ALREADY GRADED A+
Turning the Teach Pendant on: - (answer)Gives motion control solely to the
operator via the teach pendant
What must be accomplished to avoid hard-stops and over travels? - (answer)Set
Axis Limits
SHIFT and the hard key COORD will display the following menu: - (answer)The
"jog" menu
SHIFT and POINT are needed to do what? - (answer)Record the current position
of the robot
In the motion command "J P [2] 100% FINE", If you wanted to change the "FINE"
component to a "CNT100" what buttons would you press? - (answer)Select
component, then press [CHOICE]
To switch manually from one program to another, you have to be in which
screen? - (answer)Select
How many Robot I/O points are standard on a controller? - (answer)16
, 2|Page
Which soft key is pressed to display the current motion instruction defaults from
the EDIT Screen? - (answer)POINT
When creating a program, which hard key should be pressed? - (answer)Select
When using the Prog Adjust utility, which statement is correct? -
(answer)Pressing CLR_ADJ or CLR_ALL will save the enabled data values
Which of the following tasks can be performed from the FILE Menu? -
(answer)Get a default directory of the device
If while jogging the robot, you get an "in singularity" error, What must you do? -
(answer)Joint jog J5 +/- at least 10 degrees
The"Program Header Information" at the DETAIL softkey enables you to modify
the following program information, EXCEPT: - (answer)Active tool frame
What position is the suggested type of motion used to move the robot to a HOME
position? - (answer)Joint
Which softkey allows you to enter additional program instructions into a teach
pendant program? - (answer)[INST]
Which of the following is a type of I/O signal? - (answer)Digital I/O
