MSF Course Exam QUESTIONS AND ANSWERS 2025 GRADED A
{TESTBANK} LATEST VERSIONS WELL ERABORATED
What are the primary motorcycle controls? - CORRECT ANSWER •
Throttle
• Clutch Lever
• Gearshift Lever
• Front Brake
• Rear Brake
• Electric Starter
• Turn Signal Switch
• Engine Cut-Off Switch
• Speedometer & Odometer
• Horn Button
• Tachometer
• High/Low Beam Switch
What is the most common way to initiate and control a motorcycle
lean (for turns)? - CORRECT ANSWER The handlebars are the most
common way to control lean
How does a rider operate the throttle? - CORRECT ANSWER Roll it
towards you to increase engine speed and roll it back to decrease
engine speed
What does the clutch lever do? - CORRECT ANSWER Connects power
from the engine to the rear wheel
What does lifting or pressing on the shift lever accomplish? - CORRECT
ANSWER • Lifting the lever shifts the bike to a higher gear
• Pressing the lever shifts the bike to a lower gear
What is meant by shift pattern? - CORRECT ANSWER A shift or gear
pattern is the order of gears from bottom to top (1,N,2,3,4,5)
,Where are the brake controls found? - CORRECT ANSWER • Front
Brake is on the right handle grip
• Back Brake is in front of the right footrest
What is the best source of information about your motorcycle? -
CORRECT ANSWER The motorcycle owners manual
What does the fuel valve do? - CORRECT ANSWER It controls the
flow of gas to the engines
What are the positions on the fuel vavle? - CORRECT ANSWER • On
• Off
• Reserve
What does the choke control do? - CORRECT ANSWER • Provides and
enriched fuel mixture to assist in starting a cold engine
• Provides a fast idle to permit engine to warm quickly
Where is the engine cut-off switch located? - CORRECT ANSWER
Near the right handgrip
What is the function of the tachometer? - CORRECT ANSWER
Indicates engine speed
What are some common indicator lights? - CORRECT ANSWER •
Neutral
• High Beams
• Turn Signal
• Oil Pressure
• Side Stand Down
What are the steps in starting the engine? - CORRECT ANSWER •F -
Fuel - Supply turn on
•I - Ignition - Switch turned to "On"
•N - Neutral - Shift to neutral
•E - Engine Cut off Switch - put the switch in the run position
•C - Choke/Clutch - set the choke if needed or pull the clutch
,What is the friction zone? - CORRECT ANSWER The area in the clutch
movement that begins where the clutch starts to transmit power to
the rear wheel and ends just before the clutch becomes fully engages
Describe a good riding posture - CORRECT ANSWER • Back Straight
• Head & Eyes up
• Both feet on the footrest and near controls
• Knees and elbows in
• Arms relaxed and bent
• Wrist positioned low on the throttle
List the 4 steps in turning - CORRECT ANSWER • Slow - reduce speed
before a turn
• Look - turn your head and look where you want to go
• Press - initiate lean & press the handlebars in the desired direction
• Roll - roll the throttle throughout the turn slightly increasing speed
What is the value of the "Look" step - CORRECT ANSWER Helps you
maintain a smooth path of travel
What is the value in the "Roll" step? - CORRECT ANSWER Stabilizes
the suspension and improves overall control
When is the counterweight technique used? - CORRECT ANSWER In
slow, tight turns (U-Turns) the counterweight is needed
Why do you change gears? - CORRECT ANSWER To match the engine
speed with the road speed
What is the 3-Part shift process? - CORRECT ANSWER • Roll off the
throttles the clutch is squeezed
• Lift the shift lever firmly as far as it will go
• Smoothly ease out the clutch and adjust the throttle
What is engine braking? - CORRECT ANSWER Downshifting to slow
down the bike by using the engine
, How much of a motorcycles stopping power is available from the front
brake? - CORRECT ANSWER Front brakes provide 70% of stopping
power
Why should both brakes be used simultaneously? - CORRECT ANSWER
You can stop faster
What's the purpose of the range safety rules? - CORRECT ANSWER
To provide a low risk and positive learning environment
Name 3 of the more important range safety rules - CORRECT ANSWER
• DO NOT practice without rider permission from coach
• Wear protective gear when riding
• Know where the engine cut off switch is and how to use it
• Do not pass other riders unless instructed to
How will the riders coaches communicate with you on the range? -
CORRECT ANSWER • Use of hand signals during riding exercises
• Verbal Communication
What does it mean to have a space cushion? - CORRECT ANSWER
Space between your motorcycle and traffic
How does a motorcycle utilize lane position? - CORRECT ANSWER
Position yourself to see potential problems ahead and so others can
see you
Name some ways to be more visible to others in traffic - CORRECT
ANSWER •Clothing (Bright Colors)
•Headlight (During the day)
•Signals (communicate by signals)
•Brake Light (Flash before and during stops)
•Horn (use to gain attention)
What are the 3 "Lead Times"? RiderRadar - CORRECT ANSWER 2-
Seconds following distance
4-Seconds immediate path
12-Seconds anticipated path
{TESTBANK} LATEST VERSIONS WELL ERABORATED
What are the primary motorcycle controls? - CORRECT ANSWER •
Throttle
• Clutch Lever
• Gearshift Lever
• Front Brake
• Rear Brake
• Electric Starter
• Turn Signal Switch
• Engine Cut-Off Switch
• Speedometer & Odometer
• Horn Button
• Tachometer
• High/Low Beam Switch
What is the most common way to initiate and control a motorcycle
lean (for turns)? - CORRECT ANSWER The handlebars are the most
common way to control lean
How does a rider operate the throttle? - CORRECT ANSWER Roll it
towards you to increase engine speed and roll it back to decrease
engine speed
What does the clutch lever do? - CORRECT ANSWER Connects power
from the engine to the rear wheel
What does lifting or pressing on the shift lever accomplish? - CORRECT
ANSWER • Lifting the lever shifts the bike to a higher gear
• Pressing the lever shifts the bike to a lower gear
What is meant by shift pattern? - CORRECT ANSWER A shift or gear
pattern is the order of gears from bottom to top (1,N,2,3,4,5)
,Where are the brake controls found? - CORRECT ANSWER • Front
Brake is on the right handle grip
• Back Brake is in front of the right footrest
What is the best source of information about your motorcycle? -
CORRECT ANSWER The motorcycle owners manual
What does the fuel valve do? - CORRECT ANSWER It controls the
flow of gas to the engines
What are the positions on the fuel vavle? - CORRECT ANSWER • On
• Off
• Reserve
What does the choke control do? - CORRECT ANSWER • Provides and
enriched fuel mixture to assist in starting a cold engine
• Provides a fast idle to permit engine to warm quickly
Where is the engine cut-off switch located? - CORRECT ANSWER
Near the right handgrip
What is the function of the tachometer? - CORRECT ANSWER
Indicates engine speed
What are some common indicator lights? - CORRECT ANSWER •
Neutral
• High Beams
• Turn Signal
• Oil Pressure
• Side Stand Down
What are the steps in starting the engine? - CORRECT ANSWER •F -
Fuel - Supply turn on
•I - Ignition - Switch turned to "On"
•N - Neutral - Shift to neutral
•E - Engine Cut off Switch - put the switch in the run position
•C - Choke/Clutch - set the choke if needed or pull the clutch
,What is the friction zone? - CORRECT ANSWER The area in the clutch
movement that begins where the clutch starts to transmit power to
the rear wheel and ends just before the clutch becomes fully engages
Describe a good riding posture - CORRECT ANSWER • Back Straight
• Head & Eyes up
• Both feet on the footrest and near controls
• Knees and elbows in
• Arms relaxed and bent
• Wrist positioned low on the throttle
List the 4 steps in turning - CORRECT ANSWER • Slow - reduce speed
before a turn
• Look - turn your head and look where you want to go
• Press - initiate lean & press the handlebars in the desired direction
• Roll - roll the throttle throughout the turn slightly increasing speed
What is the value of the "Look" step - CORRECT ANSWER Helps you
maintain a smooth path of travel
What is the value in the "Roll" step? - CORRECT ANSWER Stabilizes
the suspension and improves overall control
When is the counterweight technique used? - CORRECT ANSWER In
slow, tight turns (U-Turns) the counterweight is needed
Why do you change gears? - CORRECT ANSWER To match the engine
speed with the road speed
What is the 3-Part shift process? - CORRECT ANSWER • Roll off the
throttles the clutch is squeezed
• Lift the shift lever firmly as far as it will go
• Smoothly ease out the clutch and adjust the throttle
What is engine braking? - CORRECT ANSWER Downshifting to slow
down the bike by using the engine
, How much of a motorcycles stopping power is available from the front
brake? - CORRECT ANSWER Front brakes provide 70% of stopping
power
Why should both brakes be used simultaneously? - CORRECT ANSWER
You can stop faster
What's the purpose of the range safety rules? - CORRECT ANSWER
To provide a low risk and positive learning environment
Name 3 of the more important range safety rules - CORRECT ANSWER
• DO NOT practice without rider permission from coach
• Wear protective gear when riding
• Know where the engine cut off switch is and how to use it
• Do not pass other riders unless instructed to
How will the riders coaches communicate with you on the range? -
CORRECT ANSWER • Use of hand signals during riding exercises
• Verbal Communication
What does it mean to have a space cushion? - CORRECT ANSWER
Space between your motorcycle and traffic
How does a motorcycle utilize lane position? - CORRECT ANSWER
Position yourself to see potential problems ahead and so others can
see you
Name some ways to be more visible to others in traffic - CORRECT
ANSWER •Clothing (Bright Colors)
•Headlight (During the day)
•Signals (communicate by signals)
•Brake Light (Flash before and during stops)
•Horn (use to gain attention)
What are the 3 "Lead Times"? RiderRadar - CORRECT ANSWER 2-
Seconds following distance
4-Seconds immediate path
12-Seconds anticipated path
