3/13/25, 12:37 PM CWB 2 VISUAL WELD INSPECTOR COMPLETE EXAM Q&A / STUDY GUIDE REVIEW / EXPERT VERIFIED ACTUAL QUESTI…
CWB 2 VISUAL WELD INSPECTOR COMPLETE
EXAM Q&A / STUDY GUIDE REVIEW / EXPERT
VERIFIED ACTUAL QUESTIONS & ANSWERS FOR
GUARANTEED PASS | NEWEST UPDATE,
Save
Terms in this set (1000)
A consumable electrode AN electrode which melts and provides metal to fill
is: the joint
the portion of the base metal adjacent to the weld
The weld heat affected
metal whose properties have been changed due to
zone is:
the heat of welding
When an arc is formed electricity flows from negative cathode to positive
between two electrodes anode
The magnetic pinch force increases as the square of the current causing smaller
helps in the process of the and smaller droplets to be detached
detaching the molten
metal drops from the
electrode tip. The
magnetic force
The electric current for High voltage, low amperage to low voltage, high
welding must be amperage
transformed from
The major advantage of full penetration welds on thick material in one pass
electron beam welding
process is
https://quizlet.com/1017751028/cwb-2-visual-weld-inspector-complete-exam-qa-study-guide-review-expert-verified-actual-questions-answers-for-guar… 1/11
, 3/13/25, 12:37 PM CWB 2 VISUAL WELD INSPECTOR COMPLETE EXAM Q&A / STUDY GUIDE REVIEW / EXPERT VERIFIED ACTUAL QUESTI…
The progress of welding Vertical up
with Electroslag welding
process is
is solid state process in which coalescence is
Explosion welding produced through high speed impacting of two or
more materials by controlled detonation
A typical application for joining of rails
thermite welding is
Welding without filler autogenous welding
metal with GTAW process
is referred to as
A typical weld flaw porosity
associated with GTAW
process is
SMAW power sources drooping
typically have a volt-
ampere curve that is
Once a box of E49XX low 4 hours
hydrogen electrodes has
been opened the
electrodes may remain at
ambient temperature for
up to a maximum of
Shielded Metal ARC establishes an arc between the end of a covered
Welding (SMAW) process electrode and the work piece.
The spray mode of metal high amperage, high voltage and argon-rich shielding
transfer is achieved with gas
have feedback systems to maintain the preset wire
digital wire feeders
feed speed
wire designated by CSA Results in weld deposit with a maximum of 8 ml
standard W48 as an E491T- diffusible hydrogen per 100 g of weld metal
9MJ-H8
https://quizlet.com/1017751028/cwb-2-visual-weld-inspector-complete-exam-qa-study-guide-review-expert-verified-actual-questions-answers-for-guar… 2/11
CWB 2 VISUAL WELD INSPECTOR COMPLETE
EXAM Q&A / STUDY GUIDE REVIEW / EXPERT
VERIFIED ACTUAL QUESTIONS & ANSWERS FOR
GUARANTEED PASS | NEWEST UPDATE,
Save
Terms in this set (1000)
A consumable electrode AN electrode which melts and provides metal to fill
is: the joint
the portion of the base metal adjacent to the weld
The weld heat affected
metal whose properties have been changed due to
zone is:
the heat of welding
When an arc is formed electricity flows from negative cathode to positive
between two electrodes anode
The magnetic pinch force increases as the square of the current causing smaller
helps in the process of the and smaller droplets to be detached
detaching the molten
metal drops from the
electrode tip. The
magnetic force
The electric current for High voltage, low amperage to low voltage, high
welding must be amperage
transformed from
The major advantage of full penetration welds on thick material in one pass
electron beam welding
process is
https://quizlet.com/1017751028/cwb-2-visual-weld-inspector-complete-exam-qa-study-guide-review-expert-verified-actual-questions-answers-for-guar… 1/11
, 3/13/25, 12:37 PM CWB 2 VISUAL WELD INSPECTOR COMPLETE EXAM Q&A / STUDY GUIDE REVIEW / EXPERT VERIFIED ACTUAL QUESTI…
The progress of welding Vertical up
with Electroslag welding
process is
is solid state process in which coalescence is
Explosion welding produced through high speed impacting of two or
more materials by controlled detonation
A typical application for joining of rails
thermite welding is
Welding without filler autogenous welding
metal with GTAW process
is referred to as
A typical weld flaw porosity
associated with GTAW
process is
SMAW power sources drooping
typically have a volt-
ampere curve that is
Once a box of E49XX low 4 hours
hydrogen electrodes has
been opened the
electrodes may remain at
ambient temperature for
up to a maximum of
Shielded Metal ARC establishes an arc between the end of a covered
Welding (SMAW) process electrode and the work piece.
The spray mode of metal high amperage, high voltage and argon-rich shielding
transfer is achieved with gas
have feedback systems to maintain the preset wire
digital wire feeders
feed speed
wire designated by CSA Results in weld deposit with a maximum of 8 ml
standard W48 as an E491T- diffusible hydrogen per 100 g of weld metal
9MJ-H8
https://quizlet.com/1017751028/cwb-2-visual-weld-inspector-complete-exam-qa-study-guide-review-expert-verified-actual-questions-answers-for-guar… 2/11
