GYPSUM CONSTRUCTION EXAM
GYPSUM CONSTRUCTION EXAM WITH GUARANTEED ACCURATE ANSWERS |
VERIFIED
_____ fastener should be used when 3/8", 1/2" and 5/8" single layer
gypsum panels are attached to wood framing.
A. 1-1/2" Type G bugle head
B. 1-1/4" Type S bugle head
C. 1-1/8" Type S bugle head
D. 1-1/4" Type W bugle head - ACCURATE ANSWERS✔✔ D. 1-1/4"
Type W bugle head
pg 39
,_____ is/are warning signs of fastener imperfections.
A. Darkening
B. Localized cracking
C. Protrusion of the fasteners
D. All of the above - ACCURATE ANSWERS✔✔ D. All of the above
pg 370
Extended periods of _____ will discolor panel face paper.
A. High humidity
B. Low humidity
C. Cold weather
D. Strong sunlight - ACCURATE ANSWERS✔✔ D. Strong sunlight
pg 355
3/8-inch gypsum panels are designed for framing centers up to _____.
A. 24 inches
B. 16 inches
,C. 20 inches
D. 12 inches - ACCURATE ANSWERS✔✔ B. 16 inches
pg 3
_____ is often caused by excessively fast drying of joint compounds.
A. Loose panels
B. Board sagging
C. Joint cracking
D. None of the above - ACCURATE ANSWERS✔✔ C. Joint cracking
pg 370
Use _____ screw to connect 3/4 inch single-layer panels to steel studs.
A. 1 inch Type S bugle head
B. 1-1/8 inch Type S bugle head
C. 1-1/4 inch Type S bugle head
D. 2-1/4 inch Type S bugle head - ACCURATE ANSWERS✔✔ C. 1-1/4
inch Type S bugle head
, pg 38
Stack panels face up with ends resting on nominal 2" x 4" lumber and
with center of the boards resting on floor, and allow to remain overnight
or until they have _____.
A. A 1" space between adjacent panels
B. At least a 2" permanent bow
C. No stains or discoloration on face paper
D. All of the above - ACCURATE ANSWERS✔✔ B. At least a 2"
permanent bow
pg 112
Maintain and control heat in the range of 55F to 70F for 24 hours _____
the entire gypsum board finishing process.
A. Before
B. During
C. After
D. All of the above - ACCURATE ANSWERS✔✔ D. All of the above
pg 103
GYPSUM CONSTRUCTION EXAM WITH GUARANTEED ACCURATE ANSWERS |
VERIFIED
_____ fastener should be used when 3/8", 1/2" and 5/8" single layer
gypsum panels are attached to wood framing.
A. 1-1/2" Type G bugle head
B. 1-1/4" Type S bugle head
C. 1-1/8" Type S bugle head
D. 1-1/4" Type W bugle head - ACCURATE ANSWERS✔✔ D. 1-1/4"
Type W bugle head
pg 39
,_____ is/are warning signs of fastener imperfections.
A. Darkening
B. Localized cracking
C. Protrusion of the fasteners
D. All of the above - ACCURATE ANSWERS✔✔ D. All of the above
pg 370
Extended periods of _____ will discolor panel face paper.
A. High humidity
B. Low humidity
C. Cold weather
D. Strong sunlight - ACCURATE ANSWERS✔✔ D. Strong sunlight
pg 355
3/8-inch gypsum panels are designed for framing centers up to _____.
A. 24 inches
B. 16 inches
,C. 20 inches
D. 12 inches - ACCURATE ANSWERS✔✔ B. 16 inches
pg 3
_____ is often caused by excessively fast drying of joint compounds.
A. Loose panels
B. Board sagging
C. Joint cracking
D. None of the above - ACCURATE ANSWERS✔✔ C. Joint cracking
pg 370
Use _____ screw to connect 3/4 inch single-layer panels to steel studs.
A. 1 inch Type S bugle head
B. 1-1/8 inch Type S bugle head
C. 1-1/4 inch Type S bugle head
D. 2-1/4 inch Type S bugle head - ACCURATE ANSWERS✔✔ C. 1-1/4
inch Type S bugle head
, pg 38
Stack panels face up with ends resting on nominal 2" x 4" lumber and
with center of the boards resting on floor, and allow to remain overnight
or until they have _____.
A. A 1" space between adjacent panels
B. At least a 2" permanent bow
C. No stains or discoloration on face paper
D. All of the above - ACCURATE ANSWERS✔✔ B. At least a 2"
permanent bow
pg 112
Maintain and control heat in the range of 55F to 70F for 24 hours _____
the entire gypsum board finishing process.
A. Before
B. During
C. After
D. All of the above - ACCURATE ANSWERS✔✔ D. All of the above
pg 103
