TTT1 Study Guide
Who is the third party group that approves and endorses standards? - ANS -American National
Standards Institute
What term is used to describe the documents written by members, or peers, in the industry? -
ANS -Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? - ANS -Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? - ANS -Employer
On a job site, who should be involved in the JHA process? - ANS -The Whole Crew
What does the Term SOW stand for? - ANS -Scope Of Work
The letters JHA stand for what ? - ANS -Job Hazard Assessment
When using an extension ladder, how many feet past the platform must it extend? - ANS -3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to be to have the correct slope? - ANS -4
Work boots with ankle support are recommended for all work sites? - ANS -True
What do the letters PPE stand for ? - ANS -Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ANS -Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ANS -Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to
your anchorage be placed?extend? - ANS -Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ANS
-Nine inches
, When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? - ANS -Four feet
What is the minimum force that a work positioning system anchorage must be able to
withstand? - ANS -Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use?
- ANS -5,000 lbs
When working, how often should fall protection equipment be inspected ? - ANS -Daily before
each use
According to the applicable industry standard, what is the minimum height from a lower surface
or ground where fall protection must be used? - ANS -Six feet
How many pounds force is one kilo Newton(kN) - ANS -225
What are the four most common types of towers used to support telecommunications antennas?
- ANS -Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? - ANS -Horizontal member
What is not a component on a guyed tower? - ANS -Gin pole
What is the purpose of a turnbuckle when working with guy wires? - ANS -Adjusts the tension
Which government organization regulates tower lighting ? - ANS -FAA
When completing tower demolition, what must you have in place before you start the job? -
ANS -Demolition permit
When completing the visual inspection of a foundation, what is one of the key items to look for?
- ANS -Cracks
What term identifies a monopole component? - ANS -Base flange
According to the manufacturers specifications, what is the minimum number of ground kits
installed on a single Run? - ANS -Three
What type of antenna is used to transmit signal from tower to tower? - ANS -Microwave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? - ANS -Above
it
Who is the third party group that approves and endorses standards? - ANS -American National
Standards Institute
What term is used to describe the documents written by members, or peers, in the industry? -
ANS -Standards
A company's health, safety and environment policy should be a combination of labor regulations
and ? - ANS -Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the acts
general clause? - ANS -Employer
On a job site, who should be involved in the JHA process? - ANS -The Whole Crew
What does the Term SOW stand for? - ANS -Scope Of Work
The letters JHA stand for what ? - ANS -Job Hazard Assessment
When using an extension ladder, how many feet past the platform must it extend? - ANS -3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to be to have the correct slope? - ANS -4
Work boots with ankle support are recommended for all work sites? - ANS -True
What do the letters PPE stand for ? - ANS -Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ANS -Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ANS -Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection to
your anchorage be placed?extend? - ANS -Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ANS
-Nine inches
, When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull out
distance? - ANS -Four feet
What is the minimum force that a work positioning system anchorage must be able to
withstand? - ANS -Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection use?
- ANS -5,000 lbs
When working, how often should fall protection equipment be inspected ? - ANS -Daily before
each use
According to the applicable industry standard, what is the minimum height from a lower surface
or ground where fall protection must be used? - ANS -Six feet
How many pounds force is one kilo Newton(kN) - ANS -225
What are the four most common types of towers used to support telecommunications antennas?
- ANS -Guyed towers, self-support towers, monopoles, and non- standard
What identifies a self-support tower? - ANS -Horizontal member
What is not a component on a guyed tower? - ANS -Gin pole
What is the purpose of a turnbuckle when working with guy wires? - ANS -Adjusts the tension
Which government organization regulates tower lighting ? - ANS -FAA
When completing tower demolition, what must you have in place before you start the job? -
ANS -Demolition permit
When completing the visual inspection of a foundation, what is one of the key items to look for?
- ANS -Cracks
What term identifies a monopole component? - ANS -Base flange
According to the manufacturers specifications, what is the minimum number of ground kits
installed on a single Run? - ANS -Three
What type of antenna is used to transmit signal from tower to tower? - ANS -Microwave dish
Where should a coax ground be placed vertically in relation to the hoisting grip? - ANS -Above
it
