Welding RED SEAL Latest Questions 100%
Correct Solutions
remove from service, or
redress with a file or whetstone ( NEVER use a grinder to redress heat-treated tools) -
ANSWER what should be done to a chisel with a mushroomed head?
NO (never punch a hole that is smaller than the thickness of the plate) - ANSWER
when using an ironworker machine, is it safe to punch a 1/2" hole into 3/4" plate?
90 degrees - ANSWER what is the included angle of the point on a centre punch?
dress the grinding stone to sharpen wheel - ANSWER if the grinding stone on a
pedestal grinder is getting dull, what should be done?
supplied air breathing apparatus - ANSWER airline respirators are also known as what?
anytime you are working above 3 meters - ANSWER when is it mandatory to wear
fall protection?
worker education, product labelling, MSDS - ANSWER what are the 3 key elements to
WHMIS?
10ppm over an 8 hour period - ANSWER what is the maximum allowable exposure
limit for H2S?
, 1/8" (3mm) MAXIMUM - ANSWER what is the distance between the tool rest and the
stone on a pedestal grinder?
2000lbs (4x the intended load) - ANSWER if a scaffold is going to hold a 500lb load, it
must be designed to hold a minimum of what weight?
24 ft (4:1 height to base ratio) - ANSWER if a free standing scaffold has a base of 6ft x
6ft what is the maximum height?
from the arrow outwards (line closest to where the arrow is pointing is done first)
- ANSWER what is the progression of welding, if weld has multiple reference lines
single bevel ( b/c only one joint member is to be bevelled) - ANSWER which weld
symbol requires a broken arrow?
0.18 % carbon - ANSWER what does the "18" represent in a 1018 steel
with a bridge Cam gauge - ANSWER how is undercut accurately measured?
3 inches - ANSWER when preheating, how far back from the joint must be up
to temperature?
tempering - ANSWER decreases hardness and increase the toughness
NEMA - ANSWER what organization rates duty cycle for power sources?
Correct Solutions
remove from service, or
redress with a file or whetstone ( NEVER use a grinder to redress heat-treated tools) -
ANSWER what should be done to a chisel with a mushroomed head?
NO (never punch a hole that is smaller than the thickness of the plate) - ANSWER
when using an ironworker machine, is it safe to punch a 1/2" hole into 3/4" plate?
90 degrees - ANSWER what is the included angle of the point on a centre punch?
dress the grinding stone to sharpen wheel - ANSWER if the grinding stone on a
pedestal grinder is getting dull, what should be done?
supplied air breathing apparatus - ANSWER airline respirators are also known as what?
anytime you are working above 3 meters - ANSWER when is it mandatory to wear
fall protection?
worker education, product labelling, MSDS - ANSWER what are the 3 key elements to
WHMIS?
10ppm over an 8 hour period - ANSWER what is the maximum allowable exposure
limit for H2S?
, 1/8" (3mm) MAXIMUM - ANSWER what is the distance between the tool rest and the
stone on a pedestal grinder?
2000lbs (4x the intended load) - ANSWER if a scaffold is going to hold a 500lb load, it
must be designed to hold a minimum of what weight?
24 ft (4:1 height to base ratio) - ANSWER if a free standing scaffold has a base of 6ft x
6ft what is the maximum height?
from the arrow outwards (line closest to where the arrow is pointing is done first)
- ANSWER what is the progression of welding, if weld has multiple reference lines
single bevel ( b/c only one joint member is to be bevelled) - ANSWER which weld
symbol requires a broken arrow?
0.18 % carbon - ANSWER what does the "18" represent in a 1018 steel
with a bridge Cam gauge - ANSWER how is undercut accurately measured?
3 inches - ANSWER when preheating, how far back from the joint must be up
to temperature?
tempering - ANSWER decreases hardness and increase the toughness
NEMA - ANSWER what organization rates duty cycle for power sources?
