RED SEAL WELDING Latest Questions
100% Correct Solutions
b) raised face slip on - ANSWER What would the abbreviation RFSO mean in a
material list?
a)reinforced fitting sock weld on
b) raised face slip on
c) reinforced fitting slide on
d) roll weld fitting slowly
c) CSA W59 - ANSWER Which standard refers to welded steel construction using
metal arc welding?
a) CSA Z662
b) CSA W178.2
c) CSA W59
d) CSA W47.1
d) phosgene gas - ANSWER When ultraviolet rays from the welding arc come into
contact with chlorinated hydrocarbon degreasers, what poisonous gas is created?
a) ethylene dichlorvos's gas
b) ozone
c) phosphine gas
d) phosgene gas
,a) proper screens and warning signs - ANSWER When welding where the general
public may be exposed to the rays of the arc, what should the welder do?
a) proper screens and warning signs
b) rope off the area
c) inform the safety coordinator
d) give a verbal warning before starting to weld
c) fiber gasket - ANSWER What would be the best type of material to use for making
a permanent template for a pipe?
a) newsprint paper
b) heavy cardboard
c) fiber gasket
d) sheet steel
d) disc thickness 1/4", rated at 12 200 rpm - ANSWER Which disc would be selected
when using a 5" grinder that has a 10,000 r.p.m. rating and grinding on the flat side
of the disc?
a. Disc thickness 3/32", rated at 12,200 r.p.m.
b. Disc thickness 1/4", rated at 8600 r.p.m.
Disc thickness 1/16", rated at 10 000 r.p.m.
d. Disc thickness 1/4", rated at 12 200 r.p.m.
c) calipers - ANSWER What tool would give you the most accurate measurement
to determine the wall thickness of pipe?
a. Tape measure.
b. Dividers.
, c. Calipers.
d. Trammel points.
a) propane - ANSWER Which fuel gas would provide the greatest amount of heat energy
for pre-heating?
a. Propane.
b. Propylene.
c. Natural Gas.
d. Acetylene.
a) trammel points - ANSWER What tool would you use to scribe large arcs and circles?
a) trammel points
b) compass
c) divider
d) chalk like
d) travel speed is too fast - ANSWER What would excessive drag lines indicate when oxy-
fuel cutting?
a. The cutting tip size is too large.
b. The oxygen pressure is too high.
c. Travel speed is too slow.
d. Travel speed is too fast.
a) detail - ANSWER Which drawing shows all dimensions and the completed
object? a. Detail.
b. Working.
100% Correct Solutions
b) raised face slip on - ANSWER What would the abbreviation RFSO mean in a
material list?
a)reinforced fitting sock weld on
b) raised face slip on
c) reinforced fitting slide on
d) roll weld fitting slowly
c) CSA W59 - ANSWER Which standard refers to welded steel construction using
metal arc welding?
a) CSA Z662
b) CSA W178.2
c) CSA W59
d) CSA W47.1
d) phosgene gas - ANSWER When ultraviolet rays from the welding arc come into
contact with chlorinated hydrocarbon degreasers, what poisonous gas is created?
a) ethylene dichlorvos's gas
b) ozone
c) phosphine gas
d) phosgene gas
,a) proper screens and warning signs - ANSWER When welding where the general
public may be exposed to the rays of the arc, what should the welder do?
a) proper screens and warning signs
b) rope off the area
c) inform the safety coordinator
d) give a verbal warning before starting to weld
c) fiber gasket - ANSWER What would be the best type of material to use for making
a permanent template for a pipe?
a) newsprint paper
b) heavy cardboard
c) fiber gasket
d) sheet steel
d) disc thickness 1/4", rated at 12 200 rpm - ANSWER Which disc would be selected
when using a 5" grinder that has a 10,000 r.p.m. rating and grinding on the flat side
of the disc?
a. Disc thickness 3/32", rated at 12,200 r.p.m.
b. Disc thickness 1/4", rated at 8600 r.p.m.
Disc thickness 1/16", rated at 10 000 r.p.m.
d. Disc thickness 1/4", rated at 12 200 r.p.m.
c) calipers - ANSWER What tool would give you the most accurate measurement
to determine the wall thickness of pipe?
a. Tape measure.
b. Dividers.
, c. Calipers.
d. Trammel points.
a) propane - ANSWER Which fuel gas would provide the greatest amount of heat energy
for pre-heating?
a. Propane.
b. Propylene.
c. Natural Gas.
d. Acetylene.
a) trammel points - ANSWER What tool would you use to scribe large arcs and circles?
a) trammel points
b) compass
c) divider
d) chalk like
d) travel speed is too fast - ANSWER What would excessive drag lines indicate when oxy-
fuel cutting?
a. The cutting tip size is too large.
b. The oxygen pressure is too high.
c. Travel speed is too slow.
d. Travel speed is too fast.
a) detail - ANSWER Which drawing shows all dimensions and the completed
object? a. Detail.
b. Working.
