Page |1
PA APPRAISERS LICENSE EXAM 2025| BRAND
NEW ACTUAL EXAM WITH 100% VERIFIED
QUESTIONS AND CORRECT SOLUTIONS|
GUARANTEED VALUE PACK| ACE YOUR
GRADES.
1. GR Pipe - correct answer - runs off the header, back of the engine, back
to air intake and back to intake manifold
2. Rear muffler - correct answer - much bigger, more of an absorption
3. Tail pipe - correct answer - takes the exhaust gases and vents out of
vehicle
4. All exhaust systems - correct answer - are sectional designs; bolted
together by exhaust flanges In-between joints are gaskets
5. Most common type of steering - correct answer - rack and pinion
6. Rack - correct answer - center of mechanism- constrained and can only
move in straight line
, Page |2
7. Pinion - correct answer - Makes the rack move
8. Steering arm - correct answer - attached to both wheels
only has rotational movement
connected to the car frame via roller bearing for turning
9. Tie rod connects the - correct answer - steering arm to the rack; can
have transitional and rotational movement
10. When rack moves - correct answer - Wheels turn at different angles;
meeting point always lies on the rear wheel line
11. Torque Converter - correct answer - In an automatic transmission,
this automatically varies the amount of torque supplied
12. Worm screw - correct answer - can fit in worm gear but not the
opposite
13. PA Adjuster Fine - correct answer - Any person who violates any of
the provisions of this act is guilty of a misdemeanor and upon conviction
, Page |3
thereof, for each offense, shall be sentenced to pay a fine not exceeding
five hundred dollars ($500), or to undergo imprisonment not exceeding
one year, or both.
14. In order for a "full release settlement" to become closed, what MUST
occur? - correct answer - The claim check must be cashed by the
claimant
15. Which of the following terms supports insurable interest? - correct
answer - Indemnity
16. What makes up the front body section in unibody designs? - correct
answer - Upper Rail, lower rail, apron assembly
17. High mount lamp goes on when - correct answer - driver hits the
brakes
18. All the following are methods used by the appraiser in determining
the value of a damaged vehicle, EXCEPT: - correct answer - A five-state
average value is correct.
, Page |4
19. In order to be eligible for an auto appraiser license, which of the
following is NOT a requirement? - correct answer - To have been
previously employed by an auto manufacturer is correct.
20. How is a diamond condition fixed? - correct answer - By pulling the
damage for length. Diamond is a length condition.
21. When measuring a unibody vehicle, it is discovered that the left front
rail is 111mm from spec in width. What condition is this? - correct
answer - Width is calculated from the center out, so a value of -111mm
on the left rail shows sway to the right and in toward centerline.
22. A collision damaged vehicle is discovered to be down in height at
opposite end of the center section. - correct answer - Twist condition.
23. When diagnosing the damage to a full frame assembly on a sport
utility vehicle, it is determined that the left side frame rail is higher than
the right side frame rail. Technician A says the damaged state is known
as a twist condition. Technician B says a sway condition exists. Who is
right? - correct answer - Tech A. When a frame rail's relationship to the
vehicle centerline is changed, such as pushed either to the left or right,
the condition is known as sway. "Twist" is referred as the condition of
the frame when entire sections are driven higher or lower than the
opposite side.
PA APPRAISERS LICENSE EXAM 2025| BRAND
NEW ACTUAL EXAM WITH 100% VERIFIED
QUESTIONS AND CORRECT SOLUTIONS|
GUARANTEED VALUE PACK| ACE YOUR
GRADES.
1. GR Pipe - correct answer - runs off the header, back of the engine, back
to air intake and back to intake manifold
2. Rear muffler - correct answer - much bigger, more of an absorption
3. Tail pipe - correct answer - takes the exhaust gases and vents out of
vehicle
4. All exhaust systems - correct answer - are sectional designs; bolted
together by exhaust flanges In-between joints are gaskets
5. Most common type of steering - correct answer - rack and pinion
6. Rack - correct answer - center of mechanism- constrained and can only
move in straight line
, Page |2
7. Pinion - correct answer - Makes the rack move
8. Steering arm - correct answer - attached to both wheels
only has rotational movement
connected to the car frame via roller bearing for turning
9. Tie rod connects the - correct answer - steering arm to the rack; can
have transitional and rotational movement
10. When rack moves - correct answer - Wheels turn at different angles;
meeting point always lies on the rear wheel line
11. Torque Converter - correct answer - In an automatic transmission,
this automatically varies the amount of torque supplied
12. Worm screw - correct answer - can fit in worm gear but not the
opposite
13. PA Adjuster Fine - correct answer - Any person who violates any of
the provisions of this act is guilty of a misdemeanor and upon conviction
, Page |3
thereof, for each offense, shall be sentenced to pay a fine not exceeding
five hundred dollars ($500), or to undergo imprisonment not exceeding
one year, or both.
14. In order for a "full release settlement" to become closed, what MUST
occur? - correct answer - The claim check must be cashed by the
claimant
15. Which of the following terms supports insurable interest? - correct
answer - Indemnity
16. What makes up the front body section in unibody designs? - correct
answer - Upper Rail, lower rail, apron assembly
17. High mount lamp goes on when - correct answer - driver hits the
brakes
18. All the following are methods used by the appraiser in determining
the value of a damaged vehicle, EXCEPT: - correct answer - A five-state
average value is correct.
, Page |4
19. In order to be eligible for an auto appraiser license, which of the
following is NOT a requirement? - correct answer - To have been
previously employed by an auto manufacturer is correct.
20. How is a diamond condition fixed? - correct answer - By pulling the
damage for length. Diamond is a length condition.
21. When measuring a unibody vehicle, it is discovered that the left front
rail is 111mm from spec in width. What condition is this? - correct
answer - Width is calculated from the center out, so a value of -111mm
on the left rail shows sway to the right and in toward centerline.
22. A collision damaged vehicle is discovered to be down in height at
opposite end of the center section. - correct answer - Twist condition.
23. When diagnosing the damage to a full frame assembly on a sport
utility vehicle, it is determined that the left side frame rail is higher than
the right side frame rail. Technician A says the damaged state is known
as a twist condition. Technician B says a sway condition exists. Who is
right? - correct answer - Tech A. When a frame rail's relationship to the
vehicle centerline is changed, such as pushed either to the left or right,
the condition is known as sway. "Twist" is referred as the condition of
the frame when entire sections are driven higher or lower than the
opposite side.
