©THESTAR 2024/2025 ALL RIGHTS RESERVED 11:42PM. A+
CML Test Exam Questions With Correct
Answers 100% Verified.
Which of the following are typical schedules found on Construction Drawing sets? -
Answer✔Door, Light Fixture, Panelboard, Room finish, Window
The portion of the construction drawing set that includes less visual and more text based
information about a project is the - Answer✔Specifications
In the most recent reorganization of construction specifications, the electrical information is
found primarily in section - Answer✔26
TRUE or FALSE: Because there is no room allocated for expansion (or growth through the
creation of new sections) new sections can only be added at the subsequent of the
Masterformat.
specific information and requirements for HVAC piping heat tracing would be located in Master
Format section,,, - Answer✔False
23 05 33
In the 2004 version, there are ? groups that contain all of the subgroups. A request for an
interpretation of the contract that may initiate contract modification would be explained in the
MasterFormat section ? - Answer✔2
01 26 13
true or false: in the 2004 version of MasterFormat each section number has four digits instead
of the prior versions that had six digits.
Specifications for commercial washers and extractors would be found in MasterFormat section
? - Answer✔false
11 23 26
1
, ©THESTAR 2024/2025 ALL RIGHTS RESERVED 11:42PM. A+
The masonry division is a part of the ? subgroup in the 2004 MasterFormat. The Requirements
for epoxy coated reinforcing steel are located in MasterFormat section ? - Answer✔Facility
Construction
03 21 16
In the NIST residence, which window types are awning windows? Select all that apply. -
Answer✔d
f
g
In which of the following areas is DWH-2 located? Enter the grid location where it is located on
the plan. - Answer✔In the garage
E-103: P12
Which circuit number and electrical panel listed below supply DWH-2? Provide the grid location
where the specifications for the disconnecting means are located. - Answer✔Circuit 17, Panel
RP-G
E-103: p11
There is only one door type 12 used in the NIST residence. What type of door is Door 12?
Provide the grid location where this information is given on the prints. - Answer✔pocket
E-103: P12
The builder must submit two 12 inch x ? samples for each type of finish coating for the
architects review of color and texture only. Provide the location of where this information is
found in the specifications. - Answer✔8"
09 90 00:1.4:b:3
Molded-case circuit breaker shunt trips must have 120-volt coils energized from a separate
circuit and set to trip at ? of the rated voltage. Provide the location of where this information is
found in the specifications. - Answer✔55%
26 24 16:2.3:b:4:e
fixture support wires for humid spaces must meet the following requirements: ASTM A 580/A
580M, Composition 302 or 304, annealed stainless steel, ?. Provide the location of where this
information is found in the specifications. - Answer✔2.68mm
26 51 00:2.6:e
2
CML Test Exam Questions With Correct
Answers 100% Verified.
Which of the following are typical schedules found on Construction Drawing sets? -
Answer✔Door, Light Fixture, Panelboard, Room finish, Window
The portion of the construction drawing set that includes less visual and more text based
information about a project is the - Answer✔Specifications
In the most recent reorganization of construction specifications, the electrical information is
found primarily in section - Answer✔26
TRUE or FALSE: Because there is no room allocated for expansion (or growth through the
creation of new sections) new sections can only be added at the subsequent of the
Masterformat.
specific information and requirements for HVAC piping heat tracing would be located in Master
Format section,,, - Answer✔False
23 05 33
In the 2004 version, there are ? groups that contain all of the subgroups. A request for an
interpretation of the contract that may initiate contract modification would be explained in the
MasterFormat section ? - Answer✔2
01 26 13
true or false: in the 2004 version of MasterFormat each section number has four digits instead
of the prior versions that had six digits.
Specifications for commercial washers and extractors would be found in MasterFormat section
? - Answer✔false
11 23 26
1
, ©THESTAR 2024/2025 ALL RIGHTS RESERVED 11:42PM. A+
The masonry division is a part of the ? subgroup in the 2004 MasterFormat. The Requirements
for epoxy coated reinforcing steel are located in MasterFormat section ? - Answer✔Facility
Construction
03 21 16
In the NIST residence, which window types are awning windows? Select all that apply. -
Answer✔d
f
g
In which of the following areas is DWH-2 located? Enter the grid location where it is located on
the plan. - Answer✔In the garage
E-103: P12
Which circuit number and electrical panel listed below supply DWH-2? Provide the grid location
where the specifications for the disconnecting means are located. - Answer✔Circuit 17, Panel
RP-G
E-103: p11
There is only one door type 12 used in the NIST residence. What type of door is Door 12?
Provide the grid location where this information is given on the prints. - Answer✔pocket
E-103: P12
The builder must submit two 12 inch x ? samples for each type of finish coating for the
architects review of color and texture only. Provide the location of where this information is
found in the specifications. - Answer✔8"
09 90 00:1.4:b:3
Molded-case circuit breaker shunt trips must have 120-volt coils energized from a separate
circuit and set to trip at ? of the rated voltage. Provide the location of where this information is
found in the specifications. - Answer✔55%
26 24 16:2.3:b:4:e
fixture support wires for humid spaces must meet the following requirements: ASTM A 580/A
580M, Composition 302 or 304, annealed stainless steel, ?. Provide the location of where this
information is found in the specifications. - Answer✔2.68mm
26 51 00:2.6:e
2
