Network Security Essentials
What are the three components of the WatchGuard System Manager software? *
A) Policy Manager, Firebox System Manager (FSM), Management Server
B) Policy Manager, Host Watch, Dimension
C) Policy Manager, Firebox System Manager (FSM), Host Watch
D) Policy Manager, Report Server, Management Server - answerC
Which of the following do you need to ensure you have when initially activating your
firewall? Choose all that apply. *
A) Firebox Serial Number
B) Feature Key
C) Account on the WatchGuard website
D) Device firmware version - answerA, C
Which account do you need to log into your WatchGuard firewall through WatchGuard
System Manager? *
A) Admin
B) Readonly
C) Status
D) Config - answerC
True or False: A Feature Key can be migrated between devices. *
True
False - answerFalse
A Feature Key is specific to a specific device, because it is based on the serial number.
What are the four types of network interfaces you can configure on your firewall? *
A) External, Trusted, Optional, Custom
B) Trusted, Primary, Optional, DHCP
C) External, Optional, Trusted, Optional
D) Optional, Trusted, Custom, Internet - answerA
True or False: There are three modes you can operate your firewall under: Mixed
Routing, Bridged and Drop-In. Bridged mode is the default selection. *
True
False - answerFalse.
Mixed Routing mode is the default mode.
What can you view directly through Firebox System Manager? Select all that apply. *
A) Gateway Wireless Controller
, B) Log Server
C) Traffic Monitor
D) Service Watch - answerA, C, D
True or False: Through Firebox System Manager, you can run the TCP Dump
command. *
True
False - answerTrue.
This option is available under the Diagnostic Tasks tool.
What is the purpose of Static NAT? *
A) To set the internal IP of a device to be different than the external IP.
B) To allow inbound access over a specific port.
C) To set both inbound and outbound access for a device on a specific IP.
D) To set a static IP on a device inside of your network. - answerB
True or False: In order to enable NAT Loopback on your firewall, you have to configure
this under the Dynamic NAT settings. *
True
False - answerFalse.
NAT Loopback does not require anything to be enabled. You simple have to write a
policy to allow it.
When you see the log "Unhandled Internal Packet," what does this mean? *
A) Someone inside of your network got blocked due to WebBlocker.
B) Someone outside of your network tried to send inbound traffic, but there was no
policy to allow it.
C) Someone inside of your network tried to send outbound traffic, but there was no
policy to allow it.
D) The firewall encountered an error when trying to review the traffic. - answerC
Which of the following services utilize firewall-based Intrusion Prevention Services?
Select all that apply. *
A) Gateway Antivirus
B) Blocked Ports
C) IPS Service
D) Blocked Sites - answerB, D
True or False: Policy precedence is most often determined by the alphabetical order of
policy names. *
True
False - answerFalse.
What are the three components of the WatchGuard System Manager software? *
A) Policy Manager, Firebox System Manager (FSM), Management Server
B) Policy Manager, Host Watch, Dimension
C) Policy Manager, Firebox System Manager (FSM), Host Watch
D) Policy Manager, Report Server, Management Server - answerC
Which of the following do you need to ensure you have when initially activating your
firewall? Choose all that apply. *
A) Firebox Serial Number
B) Feature Key
C) Account on the WatchGuard website
D) Device firmware version - answerA, C
Which account do you need to log into your WatchGuard firewall through WatchGuard
System Manager? *
A) Admin
B) Readonly
C) Status
D) Config - answerC
True or False: A Feature Key can be migrated between devices. *
True
False - answerFalse
A Feature Key is specific to a specific device, because it is based on the serial number.
What are the four types of network interfaces you can configure on your firewall? *
A) External, Trusted, Optional, Custom
B) Trusted, Primary, Optional, DHCP
C) External, Optional, Trusted, Optional
D) Optional, Trusted, Custom, Internet - answerA
True or False: There are three modes you can operate your firewall under: Mixed
Routing, Bridged and Drop-In. Bridged mode is the default selection. *
True
False - answerFalse.
Mixed Routing mode is the default mode.
What can you view directly through Firebox System Manager? Select all that apply. *
A) Gateway Wireless Controller
, B) Log Server
C) Traffic Monitor
D) Service Watch - answerA, C, D
True or False: Through Firebox System Manager, you can run the TCP Dump
command. *
True
False - answerTrue.
This option is available under the Diagnostic Tasks tool.
What is the purpose of Static NAT? *
A) To set the internal IP of a device to be different than the external IP.
B) To allow inbound access over a specific port.
C) To set both inbound and outbound access for a device on a specific IP.
D) To set a static IP on a device inside of your network. - answerB
True or False: In order to enable NAT Loopback on your firewall, you have to configure
this under the Dynamic NAT settings. *
True
False - answerFalse.
NAT Loopback does not require anything to be enabled. You simple have to write a
policy to allow it.
When you see the log "Unhandled Internal Packet," what does this mean? *
A) Someone inside of your network got blocked due to WebBlocker.
B) Someone outside of your network tried to send inbound traffic, but there was no
policy to allow it.
C) Someone inside of your network tried to send outbound traffic, but there was no
policy to allow it.
D) The firewall encountered an error when trying to review the traffic. - answerC
Which of the following services utilize firewall-based Intrusion Prevention Services?
Select all that apply. *
A) Gateway Antivirus
B) Blocked Ports
C) IPS Service
D) Blocked Sites - answerB, D
True or False: Policy precedence is most often determined by the alphabetical order of
policy names. *
True
False - answerFalse.
