International Plumbing Code Master Set questions well
answered to pass
1. All plumbing products and materials shall be listed by a third-party
certifica- tion agency as complying with the referenced standards.
2. two pipe sizes Sleeves for pipes that pass through a foundation wall shall be pipe sizes
greater than the pipe passing through the wall.
3. 6 in. 12 in. Exterior water supply system piping shall be installed not less than
inches
below frost line and not less than inches below grade.
4. 1 1/2 in. In concealed locations where piping is installed through holes or
Other than notches in studs, joists or rafters less than inches from the
cast-iron or nearest edge of the member, the pipe shall be protected by steel
galva- nized shield plates.
steel piping.
5. supported Buried piping shall be throughout its entire length.
6. 4 inches Rigid support sway bracing shall be provided at changes in direction
greater
than 45 degrees for pipe sizes inches and larger.
7. 45º Trenches installed parallel to footings shall not extend below the
-
degree bearing plane of the footing or wall.
8. 12 ft. The maximum horizontal spacing to support copper or copper-alloy pipe
Review and know feet.
how to use this
table.
9. 4 in. For pipe sizes greater than inches, restraints shall be provided for dra
pipes at all changes in direction and at all changes in diameter greater
than two pipe sizes.
, International Plumbing Code Master Set questions well
answered to pass
10. 60 in. Urinal partitions shall begin not more than 12" from and extend not less
than
Review the par- inches above the finished floor surface.
, International Plumbing Code Master Set questions well
answered to pass
tition depth re-
quirements.
11. water, air All plumbing system piping shall be tested with either or, for piping
systems other than plastic, by .
12. 15 min. When doing a drainage and vent water test, the water shall be kept in th
system,
or portion under test for at least minutes.
13. backflow Annual inspections shall be made of all prevention assemblies and air
gaps to determine whether they are operable.
14. visual The final test of the completed drainage and vent system shall be and
in
suflcient detail to determine compliance with the provisions of this code.
15. Insulated load in half.
Review the Review the excep-
changes in this
section.
16. 1 in.
Know how to
use the tables
for the exam.
17. 200
Review and
know how to
use the ta- bles
for the exam.
18. Divide the
total occupant
, International Plumbing Code Master Set questions well
answered to pass
In a parallel water
distribution system where
hot water piping is bundled
with cold or hot water
piping, each hot water
pipe shall be
.
The minimum size
condensate drainage line for
refrigeration units over 20
tons but less than 35
tons shall be
inches.
Restaurants shall have a
minimum of 1 lavatory for each
persons.
How do you determine the
occupant load for each sex
when calculating how many
plumbing fixtures are
required?
answered to pass
1. All plumbing products and materials shall be listed by a third-party
certifica- tion agency as complying with the referenced standards.
2. two pipe sizes Sleeves for pipes that pass through a foundation wall shall be pipe sizes
greater than the pipe passing through the wall.
3. 6 in. 12 in. Exterior water supply system piping shall be installed not less than
inches
below frost line and not less than inches below grade.
4. 1 1/2 in. In concealed locations where piping is installed through holes or
Other than notches in studs, joists or rafters less than inches from the
cast-iron or nearest edge of the member, the pipe shall be protected by steel
galva- nized shield plates.
steel piping.
5. supported Buried piping shall be throughout its entire length.
6. 4 inches Rigid support sway bracing shall be provided at changes in direction
greater
than 45 degrees for pipe sizes inches and larger.
7. 45º Trenches installed parallel to footings shall not extend below the
-
degree bearing plane of the footing or wall.
8. 12 ft. The maximum horizontal spacing to support copper or copper-alloy pipe
Review and know feet.
how to use this
table.
9. 4 in. For pipe sizes greater than inches, restraints shall be provided for dra
pipes at all changes in direction and at all changes in diameter greater
than two pipe sizes.
, International Plumbing Code Master Set questions well
answered to pass
10. 60 in. Urinal partitions shall begin not more than 12" from and extend not less
than
Review the par- inches above the finished floor surface.
, International Plumbing Code Master Set questions well
answered to pass
tition depth re-
quirements.
11. water, air All plumbing system piping shall be tested with either or, for piping
systems other than plastic, by .
12. 15 min. When doing a drainage and vent water test, the water shall be kept in th
system,
or portion under test for at least minutes.
13. backflow Annual inspections shall be made of all prevention assemblies and air
gaps to determine whether they are operable.
14. visual The final test of the completed drainage and vent system shall be and
in
suflcient detail to determine compliance with the provisions of this code.
15. Insulated load in half.
Review the Review the excep-
changes in this
section.
16. 1 in.
Know how to
use the tables
for the exam.
17. 200
Review and
know how to
use the ta- bles
for the exam.
18. Divide the
total occupant
, International Plumbing Code Master Set questions well
answered to pass
In a parallel water
distribution system where
hot water piping is bundled
with cold or hot water
piping, each hot water
pipe shall be
.
The minimum size
condensate drainage line for
refrigeration units over 20
tons but less than 35
tons shall be
inches.
Restaurants shall have a
minimum of 1 lavatory for each
persons.
How do you determine the
occupant load for each sex
when calculating how many
plumbing fixtures are
required?
