1/31/25, 9:48 AM CWB 2 Visual Weld Inspector Exam Actual Questions And Answers Graded A+ Flashcards | Quizlet
CWB 2 Visual Weld Inspector Exam
Actual Questions And Answers
Graded A+
Save
Terms in this set (1000)
A consumable electrode AN electrode which melts and provides metal to fill
is: the joint
the portion of the base metal adjacent to the weld
The weld heat affected
metal whose properties have been changed due to
zone is:
the heat of welding
When an arc is formed electricity flows from negative cathode to positive
between two electrodes anode
The magnetic pinch increases as the square of the current causing
force helps in the smaller and smaller droplets to be detached
process of the detaching
the molten metal drops
from the electrode tip.
The magnetic force
,1/31/25, 9:48 AM CWB 2 Visual Weld Inspector Exam Actual Questions And Answers Graded A+ Flashcards | Quizlet
The electric current for High voltage, low amperage to low voltage, high
welding must be amperage
transformed from
The major advantage of full penetration welds on thick material in one pass
electron beam welding
process is
The progress of welding Vertical up
with Electroslag welding
process is
is solid state process in which coalescence is
Explosion welding produced through high speed impacting of two or
more materials by controlled detonation
A typical application for joining of rails
thermite welding is
Welding without filler autogenous welding
metal with GTAW
process is referred to as
A typical weld flaw porosity
associated with GTAW
process is
SMAW power sources drooping
typically have a volt-
ampere curve that is
, 1/31/25, 9:48 AM CWB 2 Visual Weld Inspector Exam Actual Questions And Answers Graded A+ Flashcards | Quizlet
Once a box of E49XX 4 hours
low hydrogen electrodes
has been opened the
electrodes may remain at
ambient temperature for
up to a maximum of
Shielded Metal ARC establishes an arc between the end of a covered
Welding (SMAW) electrode and the work piece.
process
The spray mode of metal high amperage, high voltage and argon-rich
transfer is achieved with shielding gas
have feedback systems to maintain the preset wire
digital wire feeders
feed speed
wire designated by CSA Results in weld deposit with a maximum of 8 ml
standard W48 as an diffusible hydrogen per 100 g of weld metal
E491T-9MJ-H8
Self shield flux cored better able to tolerate air currents
wires are
The AWS classes metal solid wires
cored wire along with
CWB 2 Visual Weld Inspector Exam
Actual Questions And Answers
Graded A+
Save
Terms in this set (1000)
A consumable electrode AN electrode which melts and provides metal to fill
is: the joint
the portion of the base metal adjacent to the weld
The weld heat affected
metal whose properties have been changed due to
zone is:
the heat of welding
When an arc is formed electricity flows from negative cathode to positive
between two electrodes anode
The magnetic pinch increases as the square of the current causing
force helps in the smaller and smaller droplets to be detached
process of the detaching
the molten metal drops
from the electrode tip.
The magnetic force
,1/31/25, 9:48 AM CWB 2 Visual Weld Inspector Exam Actual Questions And Answers Graded A+ Flashcards | Quizlet
The electric current for High voltage, low amperage to low voltage, high
welding must be amperage
transformed from
The major advantage of full penetration welds on thick material in one pass
electron beam welding
process is
The progress of welding Vertical up
with Electroslag welding
process is
is solid state process in which coalescence is
Explosion welding produced through high speed impacting of two or
more materials by controlled detonation
A typical application for joining of rails
thermite welding is
Welding without filler autogenous welding
metal with GTAW
process is referred to as
A typical weld flaw porosity
associated with GTAW
process is
SMAW power sources drooping
typically have a volt-
ampere curve that is
, 1/31/25, 9:48 AM CWB 2 Visual Weld Inspector Exam Actual Questions And Answers Graded A+ Flashcards | Quizlet
Once a box of E49XX 4 hours
low hydrogen electrodes
has been opened the
electrodes may remain at
ambient temperature for
up to a maximum of
Shielded Metal ARC establishes an arc between the end of a covered
Welding (SMAW) electrode and the work piece.
process
The spray mode of metal high amperage, high voltage and argon-rich
transfer is achieved with shielding gas
have feedback systems to maintain the preset wire
digital wire feeders
feed speed
wire designated by CSA Results in weld deposit with a maximum of 8 ml
standard W48 as an diffusible hydrogen per 100 g of weld metal
E491T-9MJ-H8
Self shield flux cored better able to tolerate air currents
wires are
The AWS classes metal solid wires
cored wire along with
