ICC Vapor Recovery – VT Test Questions
and Answers
Type of sealant you should you use on a Phil-Tite Ball Float nipple: - Answer-Pipe dope
Number of open valves on the clean air separator: - Answer-One
You must be CERTIFIED by Healy to re-connect a Healy breakaway, True or False? - Answer-False
The type of pressure gauge is recommended to test Healy Vac - Answer-SYSA gauge measuring 0-100
WC
On new construction, after July 1, 2004, Can you install an in-ground Spill Bucket? - Answer-YES-When
Piping is monitored and with VAC
According to Executive Order 201 - Healy P/V Valve should be torqued at - Answer-20-50 ft-lbs
For a fire to burn, these (3) three primary elements must exist: - Answer-Fuel, Oxygen, Ignition Source
, When working with Electrical - Lock Out Tag Out procedures are under these guidelines. - Answer-CAL-
OSHA
Organization that certifies vapor recovery systems. - Answer-CARB or ARB
According to RP 500, a level II technician may NOT inspect this part. - Answer-Replace VP 1000 Healy
Pump
where hanging hardware repairs must be tracked. - Answer-GDF maintenance log
approved sealant when assembling a Phil-Tite Drop Tube. - Answer-JB-Kwik
Material direct bury OPW container sleeve shall be made of. - Answer-Stainless steel
What P/V vent cap shall be tightened to. - Answer-20-50 ft lbs
From dispenser to manifold - 2" diameter vapor piping ( 2" ID) and From manifold to tank - 3" diameter
vapor piping (3" ID) - Answer-Vapor piping
What is the maximum run for vapor piping? - Answer-No maximum run
How you know a nozzle spout is bad. - Answer-'BAD O-rinqs
According to PEI RP 300, on a balance Stage II vapor recovery system nozzle, Vapors typically flow in
what direction of the coaxial hose? - Answer-The outside pathway
What is the maximum allowable number of P/V caps allowed on a UST fuel system? - Answer-One
and Answers
Type of sealant you should you use on a Phil-Tite Ball Float nipple: - Answer-Pipe dope
Number of open valves on the clean air separator: - Answer-One
You must be CERTIFIED by Healy to re-connect a Healy breakaway, True or False? - Answer-False
The type of pressure gauge is recommended to test Healy Vac - Answer-SYSA gauge measuring 0-100
WC
On new construction, after July 1, 2004, Can you install an in-ground Spill Bucket? - Answer-YES-When
Piping is monitored and with VAC
According to Executive Order 201 - Healy P/V Valve should be torqued at - Answer-20-50 ft-lbs
For a fire to burn, these (3) three primary elements must exist: - Answer-Fuel, Oxygen, Ignition Source
, When working with Electrical - Lock Out Tag Out procedures are under these guidelines. - Answer-CAL-
OSHA
Organization that certifies vapor recovery systems. - Answer-CARB or ARB
According to RP 500, a level II technician may NOT inspect this part. - Answer-Replace VP 1000 Healy
Pump
where hanging hardware repairs must be tracked. - Answer-GDF maintenance log
approved sealant when assembling a Phil-Tite Drop Tube. - Answer-JB-Kwik
Material direct bury OPW container sleeve shall be made of. - Answer-Stainless steel
What P/V vent cap shall be tightened to. - Answer-20-50 ft lbs
From dispenser to manifold - 2" diameter vapor piping ( 2" ID) and From manifold to tank - 3" diameter
vapor piping (3" ID) - Answer-Vapor piping
What is the maximum run for vapor piping? - Answer-No maximum run
How you know a nozzle spout is bad. - Answer-'BAD O-rinqs
According to PEI RP 300, on a balance Stage II vapor recovery system nozzle, Vapors typically flow in
what direction of the coaxial hose? - Answer-The outside pathway
What is the maximum allowable number of P/V caps allowed on a UST fuel system? - Answer-One
