ASE BRAKES A5 TEST (EXAM 1, 2 AND 3)
LATEST 2024 ACTUAL EXAM WITH QUESTIONS
AND DETAILED SOLUTIONS (ALREADY
GRADED A+)
A drum is chattering on the brake lathe. This could be the result of: -
ANSWER>>Failure to install the dampening belt
A vehicle equipped with a hydro-boost brake system has a hard pedal with little
braking action. What could be the cause? - ANSWER>>Low power steering fluid
What could cause excessive noise while braking? - ANSWER>>Missing clips
A vehicle equipped with a "hill holding" option has an ABS code. What tool would
most likely be used to check the wheel speed sensor? - ANSWER>>Scan tool
The brake system has a soft, sinking pedal with the engine running. The brake
fluid level is at the correct height. What could be the cause? - ANSWER>>A
bypassing master cylinder
Technician A says the pins should be driven in with a brass hammer. Technician B
says the pins should be lubricated with brake fluid. Who is Correct? -
ANSWER>>Neither
Technician A says a hydro-boost system can use the power steering pump to
operate the booster. Technician B says a hydro-boost system can use engine
vacuum to operate the booster. Who is Correct? - ANSWER>>Technician A
A disc brake caliper is dragging. What could be the cause? - ANSWER>>Worn
brake pads
, The rear wheels of a front wheel drive car lockup heavy braking. Technician A says
this could be caused by faulty proportioning valve. Technician B says this could be
caused by a faulty brake booster. Who is Correct? - ANSWER>>Technician A
There is a loud growling noise only when the vehicle is steered to the right while
driving. What be the cause? - ANSWER>>Worn wheel bearing
A spongy pedal can be the result of: - ANSWER>>Leaking wheel Cylinders
A vehicle has a wheel speed sensor diagnostic trouble code. What could be the
LEAST LIKELY cause? - ANSWER>>A tire with the incorrect height
A vehicle has a squeak only when applying the brakes. What could be the cause? -
ANSWER>>Worn brake pads
During a moderate brake pedal application, with the engine running, what would
be considered a normal pressure reading on the inlet pressure gauge? -
ANSWER>>900 psi
What would be the most normal end-play specification for a set of tapered roller
front wheel bearings? - ANSWER>>0.0010"-0.0050" (0.0254mm-0.127mm)
Brake chatter can be caused by: - ANSWER>>Contaminated linings
Technician A says an analog wheel speed sensor can detect which direction the
wheel is turning. Technician B says a digital wheel speed sensor can detect which
direction the wheel is turning. Who is Correct? - ANSWER>>Technician B
What can not be the result of brake pad burnishing? - ANSWER>>Curing the metal
in the rotor
When bench bleeding a master cylinder what should be used? - ANSWER>>New
brake fluid
LATEST 2024 ACTUAL EXAM WITH QUESTIONS
AND DETAILED SOLUTIONS (ALREADY
GRADED A+)
A drum is chattering on the brake lathe. This could be the result of: -
ANSWER>>Failure to install the dampening belt
A vehicle equipped with a hydro-boost brake system has a hard pedal with little
braking action. What could be the cause? - ANSWER>>Low power steering fluid
What could cause excessive noise while braking? - ANSWER>>Missing clips
A vehicle equipped with a "hill holding" option has an ABS code. What tool would
most likely be used to check the wheel speed sensor? - ANSWER>>Scan tool
The brake system has a soft, sinking pedal with the engine running. The brake
fluid level is at the correct height. What could be the cause? - ANSWER>>A
bypassing master cylinder
Technician A says the pins should be driven in with a brass hammer. Technician B
says the pins should be lubricated with brake fluid. Who is Correct? -
ANSWER>>Neither
Technician A says a hydro-boost system can use the power steering pump to
operate the booster. Technician B says a hydro-boost system can use engine
vacuum to operate the booster. Who is Correct? - ANSWER>>Technician A
A disc brake caliper is dragging. What could be the cause? - ANSWER>>Worn
brake pads
, The rear wheels of a front wheel drive car lockup heavy braking. Technician A says
this could be caused by faulty proportioning valve. Technician B says this could be
caused by a faulty brake booster. Who is Correct? - ANSWER>>Technician A
There is a loud growling noise only when the vehicle is steered to the right while
driving. What be the cause? - ANSWER>>Worn wheel bearing
A spongy pedal can be the result of: - ANSWER>>Leaking wheel Cylinders
A vehicle has a wheel speed sensor diagnostic trouble code. What could be the
LEAST LIKELY cause? - ANSWER>>A tire with the incorrect height
A vehicle has a squeak only when applying the brakes. What could be the cause? -
ANSWER>>Worn brake pads
During a moderate brake pedal application, with the engine running, what would
be considered a normal pressure reading on the inlet pressure gauge? -
ANSWER>>900 psi
What would be the most normal end-play specification for a set of tapered roller
front wheel bearings? - ANSWER>>0.0010"-0.0050" (0.0254mm-0.127mm)
Brake chatter can be caused by: - ANSWER>>Contaminated linings
Technician A says an analog wheel speed sensor can detect which direction the
wheel is turning. Technician B says a digital wheel speed sensor can detect which
direction the wheel is turning. Who is Correct? - ANSWER>>Technician B
What can not be the result of brake pad burnishing? - ANSWER>>Curing the metal
in the rotor
When bench bleeding a master cylinder what should be used? - ANSWER>>New
brake fluid
