TTT1 Study Guide Questions And Answers
TTT1 Study Guide Questions And Answers With
Complete Solution.
Who is the third party group that approves and endorses standards? - ✔️✔️✔️American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
- ✔️✔️✔️Standards
A company's health, safety and environment policy should be a combination of labor
regulations and ? - ✔️✔️✔️Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the
acts general clause? - ✔️✔️✔️Employer
On a job site who should be involved in the JHA process? - ✔️✔️✔️The Whole Crew
What does the Term SOW stand for? - ✔️✔️✔️Scope Of Work
The letters JHA stand for what ? - ✔️✔️✔️Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? - ✔️✔️✔
️3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to by to have the correct slope? - ✔️✔️✔️4
Work boots with ankle support are recommended for all work sites? - ✔️✔️✔️True
TTT1 Study Guide Page 1
, TTT1 Study Guide Questions And Answers
What do the letters PPE stand for ? - ✔️✔️✔️Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ✔️✔️✔️Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ✔️✔️✔️Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection
to your anchorage be placed?extend? - ✔️✔️✔️Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ✔️
✔️✔️Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull
out distance? - ✔️✔️✔️Four feey
What is the minimum force that a work positioning system anchorage must be able to
withstand? - ✔️✔️✔️Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection
use? - ✔️✔️✔️5,000 lbs
When working, how often should fall protection equipment be inspected ? - ✔️✔️✔
️Daily before each use
According to the applicable industry standard, what is the minimum height from a lower
surface or ground where fall protection must be used? - ✔️✔️✔️Six feet
TTT1 Study Guide Page 2
TTT1 Study Guide Questions And Answers With
Complete Solution.
Who is the third party group that approves and endorses standards? - ✔️✔️✔️American
National Standards Institute
What term is used to describe the documents written by members, or peers, in the industry?
- ✔️✔️✔️Standards
A company's health, safety and environment policy should be a combination of labor
regulations and ? - ✔️✔️✔️Industry standards
Where OSHA has not promulgated specific standards, who is responsible for following the
acts general clause? - ✔️✔️✔️Employer
On a job site who should be involved in the JHA process? - ✔️✔️✔️The Whole Crew
What does the Term SOW stand for? - ✔️✔️✔️Scope Of Work
The letters JHA stand for what ? - ✔️✔️✔️Job Hazard Assessment
When using a extension ladder, how many feet past the platform must it extend? - ✔️✔️✔
️3
If you have a sixteen foot ladder leaning against a building wall, how many feet from the wall
does the case need to by to have the correct slope? - ✔️✔️✔️4
Work boots with ankle support are recommended for all work sites? - ✔️✔️✔️True
TTT1 Study Guide Page 1
, TTT1 Study Guide Questions And Answers
What do the letters PPE stand for ? - ✔️✔️✔️Personal Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? - ✔️✔️✔️Senses a short circuit,
prevents electrocution , shuts off the flow of electricity
Who is responsible for providing PPE? - ✔️✔️✔️Employer
When using a y-lanyard attached to your back d-ring, at what height should the connection
to your anchorage be placed?extend? - ✔️✔️✔️Shoulder level or above
What is the maximum distance between the sternal d-ring and the fixed safety climb? - ✔️
✔️✔️Nine inches
When calculating a fall distance using a "6 foot" energy absorbed, what is the maximum pull
out distance? - ✔️✔️✔️Four feey
What is the minimum force that a work positioning system anchorage must be able to
withstand? - ✔️✔️✔️Two times the arresting force of 3000lbs
What minimum force must a non-engineered anchor be able to withstand for fall protection
use? - ✔️✔️✔️5,000 lbs
When working, how often should fall protection equipment be inspected ? - ✔️✔️✔
️Daily before each use
According to the applicable industry standard, what is the minimum height from a lower
surface or ground where fall protection must be used? - ✔️✔️✔️Six feet
TTT1 Study Guide Page 2
