Vivint Smart Home Pro Final Exam
Complete Questions And Answers
12-24v CORRECT ANSWERS What is the input voltage range of the Doorbell Cam?
16.5 VAC CORRECT ANSWERS What is the output voltage of the transformer used to
power the SkyControl panel?
true CORRECT ANSWERS True or False: When programming a sensor into the sky
panel you can type in the serial number or "learn" it in by triggering the device
2 CORRECT ANSWERS When programming a DW21, which loop number is used?
1
2
3
beans and wire caps CORRECT ANSWERS Which of the following materials can you
use to group multiple ground terminals in a takeover module:
Solder
String
Wire Caps
Duct Tape
Beans
True CORRECT ANSWERS T or F: When installing the firefighter, it is required to test
the customer's existing smoke detectors
3/4" CORRECT ANSWERS When installing a DW21, what size bit should you use to
drill the hole for the sensor?
1/2"
3/8"
3/4"
1"
True CORRECT ANSWERS T or F: When installing the TAKE-345, you must ensure
that the transformer is supplying power to the power supply before the battery.
True CORRECT ANSWERS T or F: You are required to test signals from all secondary
keypads and key fobs even though they are not detection devices
False CORRECT ANSWERS T or F: When running power to the TAKE-345 polarity
does not apply
CORRECT ANSWERS What is the correct height at which to install the PIR2?
, 7 ft
At least 5 ft
At least 7 ft
At 7.5 ft
How would you program a CO3 if mounted on a hallway wall?
Loop 1 Zone 8
Loop 1 Zone 14
Loop 3 Zone 4
Loop 1 Zone 4 CORRECT ANSWERS
When installing a DW21 into a metal door frame, with a wooden door, what should you
be sure to use?
Metal Drill bit
A DW11 should be used on all metal door frames
3/4" insulated magnet
Eye goggles CORRECT ANSWERS
True CORRECT ANSWERS T or F: Panic Pendants are programmed as an audible
alarm
T or F: The Firefighter may be installed next to a stand-alone battery-powered smoke
detector CORRECT ANSWERS
Which of the following zone/sensor types are correct when programming an SMKT3?
Type 9 - Freeze Detect
Type 7 - Freeze Detect
Type 9 - Heat detect
Type 6 - heat detect
type 1 - heat detect
type 8 - freeze detect
type 5 - smoke detect
type 7 - smoke detect
type 9 - smoke detect CORRECT ANSWERS
When installing a DW21 where is the approved location for the sensor?
Anywhere in the door
between 6"(15 cm) and 2' (61 cm) from floor
Below 6" from the floor
Top of the door CORRECT ANSWERS
T or F: When performing a full system test, you may bypass any open doors or windows
CORRECT ANSWERS
T or F: When installing a translator, you must program all of the existing sensors as new
equipment on the panel CORRECT ANSWERS
Complete Questions And Answers
12-24v CORRECT ANSWERS What is the input voltage range of the Doorbell Cam?
16.5 VAC CORRECT ANSWERS What is the output voltage of the transformer used to
power the SkyControl panel?
true CORRECT ANSWERS True or False: When programming a sensor into the sky
panel you can type in the serial number or "learn" it in by triggering the device
2 CORRECT ANSWERS When programming a DW21, which loop number is used?
1
2
3
beans and wire caps CORRECT ANSWERS Which of the following materials can you
use to group multiple ground terminals in a takeover module:
Solder
String
Wire Caps
Duct Tape
Beans
True CORRECT ANSWERS T or F: When installing the firefighter, it is required to test
the customer's existing smoke detectors
3/4" CORRECT ANSWERS When installing a DW21, what size bit should you use to
drill the hole for the sensor?
1/2"
3/8"
3/4"
1"
True CORRECT ANSWERS T or F: When installing the TAKE-345, you must ensure
that the transformer is supplying power to the power supply before the battery.
True CORRECT ANSWERS T or F: You are required to test signals from all secondary
keypads and key fobs even though they are not detection devices
False CORRECT ANSWERS T or F: When running power to the TAKE-345 polarity
does not apply
CORRECT ANSWERS What is the correct height at which to install the PIR2?
, 7 ft
At least 5 ft
At least 7 ft
At 7.5 ft
How would you program a CO3 if mounted on a hallway wall?
Loop 1 Zone 8
Loop 1 Zone 14
Loop 3 Zone 4
Loop 1 Zone 4 CORRECT ANSWERS
When installing a DW21 into a metal door frame, with a wooden door, what should you
be sure to use?
Metal Drill bit
A DW11 should be used on all metal door frames
3/4" insulated magnet
Eye goggles CORRECT ANSWERS
True CORRECT ANSWERS T or F: Panic Pendants are programmed as an audible
alarm
T or F: The Firefighter may be installed next to a stand-alone battery-powered smoke
detector CORRECT ANSWERS
Which of the following zone/sensor types are correct when programming an SMKT3?
Type 9 - Freeze Detect
Type 7 - Freeze Detect
Type 9 - Heat detect
Type 6 - heat detect
type 1 - heat detect
type 8 - freeze detect
type 5 - smoke detect
type 7 - smoke detect
type 9 - smoke detect CORRECT ANSWERS
When installing a DW21 where is the approved location for the sensor?
Anywhere in the door
between 6"(15 cm) and 2' (61 cm) from floor
Below 6" from the floor
Top of the door CORRECT ANSWERS
T or F: When performing a full system test, you may bypass any open doors or windows
CORRECT ANSWERS
T or F: When installing a translator, you must program all of the existing sensors as new
equipment on the panel CORRECT ANSWERS
