STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
A generating station has one 1000 Kw and two 2000 Kw
generators. To supply 2000 Kw MOST economically, the
operating conditions should be - <<<Answers>>>>one 2000
Kw generator at full load
The terminal voltage of a DC shunt generator having an
armature current of 100 amperes, an armature resistance of
0.02 ohms, and a generated E.M.F of 222 volts is MOST
NEARLY ______________ volts. - <<<Answers>>>>220
The MAXIMUM pressure in an upright cylinder 6 feet in
diameter, 8 feet high, and open at the top, when filled tot he
brim with water, is MOSTLY NEARLY ______________
lbs/sq.ft. - <<< Before putting an aerosol container for
garbage pickup, it is good practice to - <<<Answers>>>>use
out the contents inn normal manner
A lantern ring is a type of - <<<Answers>>>>sealing
arrangement used to minimize air leakage between a rotating
shaft and a sleeve
Monel metal is an alloy used for water heaters tanks. It is a
combination MAINLY of - <<<Answers>>>>nickel and
copper
The plumbing fitting shown at the right is called -
<<<Answers>>>>Return Bend
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
A galvanized steel plate is a plate with a coating of -
<<<Answers>>>>zinc
If the barrel of a standard micrometer is rotated through one
complete revolution, the gap dimensions is charged by
______________ inch. - <<<Answers>>>>.025
Of the following, the indication that a fluorescent lamp is in
need of replacement is that - <<<Answers>>>>the lamp
flashes on and off, and there are black coating at the end
The one of the following that is recommended for prime-
coating bare metal is - <<<Answers>>>>zinc chromate
Dressing a grinding wheel refers to -
<<<Answers>>>>cleaning the grinding surface and making
the wheel rounds
A fusible metal plug is a protective device that -
<<<Answers>>>>melts when its temperature reaches a
specific figure
Of the following, the material that is beginning to used for
electrical conduit, plastic water pipes, and electrician
insulation is - <<<Answers>>>>polyvinylchloride
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
At certain of speed, pressure, and temperature, centrifugal
pumps can be made to cavitate. The conditions causing
cavitation - <<<Answers>>>>should be avoided since the
impeller may become seriously pitted
A nut is turned on a 1/2" - 10 bolt When the nut is turned
through five complete turns on the bolt, the distance it moves
longitudinally on the bolt is _________inch. -
<<<Answers>>>>.500
A growler is a device used for - <<<Answers>>>>detecting
shorts in armatures
Assume that certain work assignments are not liked by any of
your subordinates. As this works has to be done, you, as the
stationary engineer (electric), should try as much as possible
to - <<<Answers>>>>rotate the work assignments among
subordinates
A stationary engineer (electric), in discussing new department
regulations with his subordinates, commented, We should be
conscious of that our interests are mutual, and that by all of us
in unison putting our shoulders to the wheel and working
together, we can achieve our common objective, This
approach is _____________, because it will _____________.
- <<<Answers>>>>good; promote cooperation
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
In the inspection of relays, the type of trouble encountered
often depends on the type of relay. The one of the following
which is NOT a trouble encountered with an induction type
relay is - <<<Answers>>>>foreign matter in gear train
It is sometimes desirable to have a control that will cause a
DC motor to come to a standstill quickly instead of coasting
to a standstill after the stop button is pressed. This result is
MOST commonly obtained by means of an action called -
<<<Answers>>>>dynamic braking
In an electric circuit, a high spot temperature is MOST
commonly due to - <<<Answers>>>>a defective connection
The MAIN reason for periodic inspections and testing of
equipment in an electrically powered plant is to -
<<<Answers>>>>discover minor faults before they have a
chance to become significantly serious
Assume that an employee calls up to give advance notice of
his intentions to be absent the following day. The MOST
important information that he should give is the -
<<<Answers>>>>reasons for his absence
2025)EXAM
A generating station has one 1000 Kw and two 2000 Kw
generators. To supply 2000 Kw MOST economically, the
operating conditions should be - <<<Answers>>>>one 2000
Kw generator at full load
The terminal voltage of a DC shunt generator having an
armature current of 100 amperes, an armature resistance of
0.02 ohms, and a generated E.M.F of 222 volts is MOST
NEARLY ______________ volts. - <<<Answers>>>>220
The MAXIMUM pressure in an upright cylinder 6 feet in
diameter, 8 feet high, and open at the top, when filled tot he
brim with water, is MOSTLY NEARLY ______________
lbs/sq.ft. - <<< Before putting an aerosol container for
garbage pickup, it is good practice to - <<<Answers>>>>use
out the contents inn normal manner
A lantern ring is a type of - <<<Answers>>>>sealing
arrangement used to minimize air leakage between a rotating
shaft and a sleeve
Monel metal is an alloy used for water heaters tanks. It is a
combination MAINLY of - <<<Answers>>>>nickel and
copper
The plumbing fitting shown at the right is called -
<<<Answers>>>>Return Bend
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
A galvanized steel plate is a plate with a coating of -
<<<Answers>>>>zinc
If the barrel of a standard micrometer is rotated through one
complete revolution, the gap dimensions is charged by
______________ inch. - <<<Answers>>>>.025
Of the following, the indication that a fluorescent lamp is in
need of replacement is that - <<<Answers>>>>the lamp
flashes on and off, and there are black coating at the end
The one of the following that is recommended for prime-
coating bare metal is - <<<Answers>>>>zinc chromate
Dressing a grinding wheel refers to -
<<<Answers>>>>cleaning the grinding surface and making
the wheel rounds
A fusible metal plug is a protective device that -
<<<Answers>>>>melts when its temperature reaches a
specific figure
Of the following, the material that is beginning to used for
electrical conduit, plastic water pipes, and electrician
insulation is - <<<Answers>>>>polyvinylchloride
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
At certain of speed, pressure, and temperature, centrifugal
pumps can be made to cavitate. The conditions causing
cavitation - <<<Answers>>>>should be avoided since the
impeller may become seriously pitted
A nut is turned on a 1/2" - 10 bolt When the nut is turned
through five complete turns on the bolt, the distance it moves
longitudinally on the bolt is _________inch. -
<<<Answers>>>>.500
A growler is a device used for - <<<Answers>>>>detecting
shorts in armatures
Assume that certain work assignments are not liked by any of
your subordinates. As this works has to be done, you, as the
stationary engineer (electric), should try as much as possible
to - <<<Answers>>>>rotate the work assignments among
subordinates
A stationary engineer (electric), in discussing new department
regulations with his subordinates, commented, We should be
conscious of that our interests are mutual, and that by all of us
in unison putting our shoulders to the wheel and working
together, we can achieve our common objective, This
approach is _____________, because it will _____________.
- <<<Answers>>>>good; promote cooperation
, STATIONARY ENGINEER ELECTRIC (2024-
2025)EXAM
In the inspection of relays, the type of trouble encountered
often depends on the type of relay. The one of the following
which is NOT a trouble encountered with an induction type
relay is - <<<Answers>>>>foreign matter in gear train
It is sometimes desirable to have a control that will cause a
DC motor to come to a standstill quickly instead of coasting
to a standstill after the stop button is pressed. This result is
MOST commonly obtained by means of an action called -
<<<Answers>>>>dynamic braking
In an electric circuit, a high spot temperature is MOST
commonly due to - <<<Answers>>>>a defective connection
The MAIN reason for periodic inspections and testing of
equipment in an electrically powered plant is to -
<<<Answers>>>>discover minor faults before they have a
chance to become significantly serious
Assume that an employee calls up to give advance notice of
his intentions to be absent the following day. The MOST
important information that he should give is the -
<<<Answers>>>>reasons for his absence
