• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 3 out of 20 pages
Exam (elaborations)

Arduino Exam Study Set

Document preview thumbnail
Preview 3 out of 20 pages

ARDUINO EXAM STUDY SET...

Content preview

Arduino devices are programmed using Arduino IDE software that is
available for Windows OS, Mac OS, and Linux OS. - ANSWER t

There are many versions of the Arduino PIC board. We used the
DFRduino and duemilanove boards in class lab projects. - ANSWER t

A resistor is a device having a designed resistance to the passage of an
electric current. We used them with the Arduino board and LED's in our
blink and tone sound circuits. - ANSWER t

Resistor values are measured in the unit "R" for resistance. - ANSWER
f

LED's will work regardless of how they are connected in a circuit. This is
because they are polarized circuit components that have a cathode and
anode terminal. - ANSWER f

The "virtual" circuits development environment we use is called
TinkerCAD. It is an app that you install on your PC and then run on any
web browser. - ANSWER f

The positive end of an LED is the "anode" end. This lead is normally
longer than the negative lead and sometimes bent from the factory to
indicate it is the positive end. - ANSWER t

The Arduino IDE software uses a block structure style programming
editor to write code that uses { and } curly braces. - ANSWER t

The function of a piezo speaker is to output sound created by the
Arduino, but it also doubles as a microphone input device. - ANSWER f

The Arduino board has 14 input/output ports that are programmable. -
ANSWER t

,The "pinOut (3, OUTPUT)" command in Arduino configures the specified
pin to behave either as an input or an output. In this case, pin 3 on the
Arduino board has been specified to behave as an output pin. -
ANSWER f

The command "digitalWrite (3, x)" controls the behaviour of a designated
pin (in this case pin 3) and either turns it on or off by replacing the "x"
and using the keywords "HIGH" or "LOW". - ANSWER t

We use resistors in our Arduino circuits to control the voltage and
current going into our components ensuring we don't damage them. -
ANSWER t

The Arduino has 6 PWM ports. PWM stands for Pulse Width Modulation.
These ports were used in our LED fade circuits. - ANSWER t

For Loops used in Arduino programs can help in avoiding copying nad
pasting code that needs to be run many times in a program. - ANSWER
t

The For Loop below shows a counter that will execute 8 times because
the counter starts at zero.

for (int count = 0; count <7; count ++){
.....
} - ANSWER f

The analogWrite(....., ....); method in Arduino programming is used to
control LED's to simulate a fading effect. - ANSWER t

A Seven Segment Display can have a common that is either anode (+)
or cathode (-) - ANSWER f

When using a 7 Segment Display component, you need to use one
resistor for each of the 7 segments to avoid burning out the LED
segments. - ANSWER t

, The decimal point is not one of the 7 segments in a seven segment
display component. It is a separate connection on the component with its
own pinout. - ANSWER t

To display desired numbers on a 7 Segment Display, we use the method
/ command:

analogWrite (pin, HIGH) ) ; - ANSWER f

The DFRduino controller gets its power from both the USB port when
connected, or the battery pack supplied on the robot vehicles. -
ANSWER t

On the Arduino, there are two power terminals: GROUND and +5V. Use
of these is determined by the type of circuit and components used on the
Arduino. - ANSWER t

The 7 Segment Display component must be placed over the "BRIDGE"
of the breadboard to ensure access to all contacts on the component are
accessible. . - ANSWER f

With the DFRduino Robot Vehicle Controller, there are two motor
outputs that control 4 motors. - ANSWER t

The DFRduino controller must get power from both the USB and the
external battery power source SIMULTANEOUSLY in order to work. -
ANSWER f

When programming the DFRduino robot controller, the USB cable must
be connected and the power to the vehicle turned on so that motors will
know when to activate. - ANSWER f

On the DFRduino robot controller, the front right and rear right motors
are connected to the Servo Power input, while the front left and rear left
motors are connected to the Motor Power input ports. - ANSWER f

A photoresistor exhibits a characteristic commonly called
photoconductivity. - ANSWER t

Document information

Uploaded on
November 1, 2024
Number of pages
20
Written in
2024/2025
Type
Exam (elaborations)
Contains
Unknown
$12.99

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
Humat
4.0
(6)
Sold
43
Followers
4
Items
1252
Last sold
2 months ago




Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions