Fdny A35 (2024-2025) Exam Questions with
Answers
Leaks - <<,aNSWERS>>>CF must look & listen for leaks.
More prominent in colder months when sealing materials
shrink.
Most leakage occurs at tubing and fittings at air reciever tank.
Heat & Compressor - <<,aNSWERS>>>-never place
combustible materials nearby;
-do not use near devices that produce heat;
solar heat is not known to cause overheating
Maintenance-Pressure Relief Valve - <<,aNSWERS>>>Run
compressor w/ pressure switch fully open (when it is in this
position it CANNOT shut down the compressor).
Should be set at NO LESS than 15 psi OR 10% above the
operating pressure of the compressor (which ever is greater)
BUT NEVER higher than max allowabe working pressure of
receiver.
Maintenance-Operating Temperature -
<<,aNSWERS>>>Acceptable temp are in the maintenance
manual.
, Fdny A35 (2024-2025) Exam Questions with
Answers
Overheating can cause damage to compressor and is a
potential fire hazard.
If overheating discovered water cooling mechanism must be
checked.
Lockout/Tagout Safety Procedures - <<,aNSWERS>>>Lock
the device or the power source w/ a hasp and placing it in
such a position that no hazardous power sources can be turned
on. Also requires a tag to be affixed to the lockout device
indicating it should not be turned on.
Know OSHA Standard for Control of Hazardous Energy
(Lockout/Tagout) procedure.
Compliance w/ Lockout/Tagout - <<,aNSWERS>>>prevents
120 fatalities and 50,000 injuries each year.
Workers lose an average of 24 workdays for recuperation
from exposure to hazardous energy.
CF Responsibility - <<,aNSWERS>>>-visually inspect
-remain in area for a few minutes after compressor started
-do not operate at speeds above recommended ranged
Answers
Leaks - <<,aNSWERS>>>CF must look & listen for leaks.
More prominent in colder months when sealing materials
shrink.
Most leakage occurs at tubing and fittings at air reciever tank.
Heat & Compressor - <<,aNSWERS>>>-never place
combustible materials nearby;
-do not use near devices that produce heat;
solar heat is not known to cause overheating
Maintenance-Pressure Relief Valve - <<,aNSWERS>>>Run
compressor w/ pressure switch fully open (when it is in this
position it CANNOT shut down the compressor).
Should be set at NO LESS than 15 psi OR 10% above the
operating pressure of the compressor (which ever is greater)
BUT NEVER higher than max allowabe working pressure of
receiver.
Maintenance-Operating Temperature -
<<,aNSWERS>>>Acceptable temp are in the maintenance
manual.
, Fdny A35 (2024-2025) Exam Questions with
Answers
Overheating can cause damage to compressor and is a
potential fire hazard.
If overheating discovered water cooling mechanism must be
checked.
Lockout/Tagout Safety Procedures - <<,aNSWERS>>>Lock
the device or the power source w/ a hasp and placing it in
such a position that no hazardous power sources can be turned
on. Also requires a tag to be affixed to the lockout device
indicating it should not be turned on.
Know OSHA Standard for Control of Hazardous Energy
(Lockout/Tagout) procedure.
Compliance w/ Lockout/Tagout - <<,aNSWERS>>>prevents
120 fatalities and 50,000 injuries each year.
Workers lose an average of 24 workdays for recuperation
from exposure to hazardous energy.
CF Responsibility - <<,aNSWERS>>>-visually inspect
-remain in area for a few minutes after compressor started
-do not operate at speeds above recommended ranged
