EUNICE
Final Exam Elevator WITH 100% SURE ANSWERS
Terms in this set (137)
wrench used for rail installation spud wrench
The minimum clearance form the floor to a. 80"
the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2"
what should you be aware of when b. The original weight and counterbalancing.
removing a cab for replacement?
a. The weight that is to be removed from
the ceiling.
b. The original weight and
counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get
banged up.
When fans are used on modernization jobs d. They should direct the fumes to the outside.
for exhausting fumes, what statement is
correct?
a. They're to keep you cool, not for
exhausting fumes.
b. They should direct the fumes into the
hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the
outside.
The star symbol is used on the COP for b. To designate the main floor.
what?
a. To show where the floor buttons are
located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location.
1/17
,Using a laminate stop strip against the c. Keeps the laminate from slipping under the fence.
fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the
blade.
c. Keeps the laminate from slipping under
the fence.
d. Keeps the laminate from going over the
fence.
The contact adhesives must be ________ b. Dry
before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold
What is the most important piece of b. safety glasses
equipment you have when using a power
saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square
When using a circular saw, which of the a. Never start the cut until the blade is turning full RPM
following is correct?
a. Never start the cut until the blade is
turning full RPM
b. The base is not adjustable for cutting
depth
c. Circular saw blades range from 10 to 16
inches
d. Remove the retractable guard before
cutting
What is used to make crosscuts on a table c. Miter saw
saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade
When making crosscuts with a radial arm b. Restrain the blade from moving too fast
saw which statement is correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the
guide.
d. Adjust the blade 1/4" above to cutting
surface
2/17
, What are the two things a compound mitre d. bevel and mitre cuts can be made at the same time
saw does best at the same time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same
time.
c. Tilting the blade 45 degrees and pivoting
the table 45 degrees gives you a 90
degree square cut.
d. bevel and mitre cuts can be made at the
same time
Why do we use laminated glass in the walls b. if the glass cracks the plastic interlayer holds the fragments
of glass elevator cabs?
a. if the glass breaks you can get a
replacement at the hardware store.
b. if the glass cracks the plastic interlayer
holds the fragments
c. it is made in a variety of colors
d. it is easy to handle and installs quickly
Which of the following is NOT a step in b. mount handrails on the walls where the panels will be installed
preparing the walls before hanging
panels?
a. check walls for square and plumb
b. mount handrails on the walls where the
panels will be installed.
c. clean surfaces and fill all holes not being
used
d. preheat walls as per specifications
When installing a resilient tile floor c. 15 lb asphalt paper
covering, there should be a layer of ________
between the underlayment and the tiles.
a. plywood
b. grout
c. 15lb asphalt paper
d. tile separators
While similar to laying resilient floor tiles, a. grouting and sealing
ceramic tiles require the additional steps of:
a. grouting and sealing
b. stress testing and certification
c. glazing and firing
d. marking and cutting
Once you are satisfied with the layout of d.d lay them out in an adjacent area to maintain the floor pattern correctly
the tiles after a dry layout, remove them
and
a. stack them neatly in a location near the
entrance
b. adhere adjoining tile edges so the floor
pattern won't be lost
c. test each tile for durability
d. lay them out in an adjacent area to
maintain the floor pattern correctly.
3/17
Final Exam Elevator WITH 100% SURE ANSWERS
Terms in this set (137)
wrench used for rail installation spud wrench
The minimum clearance form the floor to a. 80"
the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2"
what should you be aware of when b. The original weight and counterbalancing.
removing a cab for replacement?
a. The weight that is to be removed from
the ceiling.
b. The original weight and
counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get
banged up.
When fans are used on modernization jobs d. They should direct the fumes to the outside.
for exhausting fumes, what statement is
correct?
a. They're to keep you cool, not for
exhausting fumes.
b. They should direct the fumes into the
hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the
outside.
The star symbol is used on the COP for b. To designate the main floor.
what?
a. To show where the floor buttons are
located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location.
1/17
,Using a laminate stop strip against the c. Keeps the laminate from slipping under the fence.
fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the
blade.
c. Keeps the laminate from slipping under
the fence.
d. Keeps the laminate from going over the
fence.
The contact adhesives must be ________ b. Dry
before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold
What is the most important piece of b. safety glasses
equipment you have when using a power
saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square
When using a circular saw, which of the a. Never start the cut until the blade is turning full RPM
following is correct?
a. Never start the cut until the blade is
turning full RPM
b. The base is not adjustable for cutting
depth
c. Circular saw blades range from 10 to 16
inches
d. Remove the retractable guard before
cutting
What is used to make crosscuts on a table c. Miter saw
saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade
When making crosscuts with a radial arm b. Restrain the blade from moving too fast
saw which statement is correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the
guide.
d. Adjust the blade 1/4" above to cutting
surface
2/17
, What are the two things a compound mitre d. bevel and mitre cuts can be made at the same time
saw does best at the same time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same
time.
c. Tilting the blade 45 degrees and pivoting
the table 45 degrees gives you a 90
degree square cut.
d. bevel and mitre cuts can be made at the
same time
Why do we use laminated glass in the walls b. if the glass cracks the plastic interlayer holds the fragments
of glass elevator cabs?
a. if the glass breaks you can get a
replacement at the hardware store.
b. if the glass cracks the plastic interlayer
holds the fragments
c. it is made in a variety of colors
d. it is easy to handle and installs quickly
Which of the following is NOT a step in b. mount handrails on the walls where the panels will be installed
preparing the walls before hanging
panels?
a. check walls for square and plumb
b. mount handrails on the walls where the
panels will be installed.
c. clean surfaces and fill all holes not being
used
d. preheat walls as per specifications
When installing a resilient tile floor c. 15 lb asphalt paper
covering, there should be a layer of ________
between the underlayment and the tiles.
a. plywood
b. grout
c. 15lb asphalt paper
d. tile separators
While similar to laying resilient floor tiles, a. grouting and sealing
ceramic tiles require the additional steps of:
a. grouting and sealing
b. stress testing and certification
c. glazing and firing
d. marking and cutting
Once you are satisfied with the layout of d.d lay them out in an adjacent area to maintain the floor pattern correctly
the tiles after a dry layout, remove them
and
a. stack them neatly in a location near the
entrance
b. adhere adjoining tile edges so the floor
pattern won't be lost
c. test each tile for durability
d. lay them out in an adjacent area to
maintain the floor pattern correctly.
3/17