A17 Telehandler Revision Questions and Answers

A17 Telehandler Revision Questions and Answers When working in a confined area or space: a) what danger can be present with regards to the counterweight of the machine, b) when should measures be taken and c) what measures should be implemented? - Answer️️ -a) the gap between the counterweight and a structure being reduced or contacting structure/object when slewing. b) when the gap will be less than 600mm. c) ensure sufficient clearance or block off access routes Apart from the operator, who else may need to use the machine's Operator's Manual? - Answer️️ -Supervisors, fitters, low loader drivers Using the lifting capacity diagram for A17: a) what is the maximum lifting capacity at maximum height, b) what is the lifting capacity with the boom angle at 45 degrees and a boom extension of 2.5 metres and TITLE: EMILLYCHARLOTTE 2024/2025 ACADEMIC PERIOD OWNER: EMILLYCHARLOTTE COPYRIGHT STATEMENT: ©2024 EMILLYCHARLOTTE. ALL RIGHTS RESERVED FIRST PUBLISHED: SEPTEMBER 2024 2/18 c) what is the farthest distance (measured from the front tyres) available to place a 1.3 tonnes load at a height of 4 metres? - Answer️️ -a) 3.3 tonnes or 3300 kilograms b) 2.5 tonnes or 2500 kilograms c) 5.3 metres Name THREE ways that a plant operator can contribute in ensuring repeat business with the client or principal contractor - Answer️️ -1. Compliance with the method Statements. 2. Cooperation with the workforce. 3. Safe working practices. 4. Work Efficiently. 5. Punctuality According to regulations (such as Lifting Operations and Lifting Equipment Regulations (LOLER) 1998) name TWO requirements that must be carried out on any lifting operation. - Answer️️ -Lifts must be properly PLANNED and SUPERVISED Name THREE ways in which an operator can minimise their impact upon the environment whilst using the machine. - Answer️️ -1. Lower engine speed, 2. correct disposal of waste, 3. follow method statements, 4. well maintained machine. TITLE: EMILLYCHARLOTTE 2024/2025 ACADEMIC PERIOD OWNER: EMILLYCHARLOTTE COPYRIGHT STATEMENT: ©2024 EMILLYCHARLOTTE. ALL RIGHTS RESERVED FIRST PUBLISHED: SEPTEMBER 2024 3/18 If a load is being lifted whilst the telehandler is on a slope and facing downhill, what effect could this have on the machine? - Answer️️ -Load centre/centre of gravity can increase causing instability An operator has been asked to transport a load along the public highway from one site to another, for which The Road Traffic Act applies. What needs to be taken into account regarding the law? - Answer️️ -Depending on vehicle classification, movement of loads is restricted to certain distances. (normally maximum of 1000 yards) Why should a telehandler be refuelled at the end of the day? - Answer️️ -To minimise condensation build up in the fuel system. Name FOUR different types or levels of disciplinary actions or sanctions that can be applied (by employers and judicial bodies) to operators of plant who do not comply with, or follow legislation and regulations. - Answer️️ -1. Verbal warnings 2. Written Warnings 3. Loss of Job (Dismissal) 4. Prosecution 5. Fine 6. Prison Sentence a) What is meant by the lifting or rated capacity of the telehandler, and b) who determines it? - Answer️️ -a) The maximum lifting capacity for a given load centre TITLE: EMILLYCHARLOTTE 2024/2025 ACADEMIC PERIOD OWNER: EMILLYCHARLOTTE COPYRIGHT STATEMENT: ©2024 EMILLYCHARLOTTE. ALL RIGHTS RESERVED FIRST PUBLISHED: SEPTEMBER 2024 4/18 b) the manufacturer Using the Operator's Manual, state the figure for the tyre pressures. Note: The Operator's Manual for the machine being used for the test MUST be available for reference by the candidate - Answer️️ -The operators Manual will be provided by the test centre and you will have to look at the index and find the Tyre chapter go there and read the figure for the tyre pressure. (The page number must be read as well) D8 Explain ALL visual checks that must be carried out on all types of quick-hitch attaching systems before use - Answer️️ -1. No visible damage to the coupler 2. Attachment. 3. Hoses and other components. 4. All components available and fitted correctly. 5. Any locking system active/in place. 6. Locking pin (if used) in the correct hole. During work, the engine starts to overheat. Explain the danger if someone tries to remove the radiator or expansion tank cap. - Answer️️ -The cooling system is normally pressurised and removing the cap can allow hot water to escape uncontrollably with the potential of causing severe burns What are the THREE actions or stages that a telehandler operator undertakes during pre-use inspections? - Answer️️ -Carry out checks according to MANUFACTURERS requirements (as a minimum), RECORD when checks have been performed, REPORT any defects IMMEDIATELY. TITLE: EMILLYCHARLOTTE 2024/2025 ACADEMIC PERIOD OWNER: EMILLYCHARLOTTE COPYRIGHT STATEMENT: ©2024 EMILLYCHARLOTTE. ALL RIGHTS RESERVED FIRST PUBLISHED: SEPTEMBER 2024 5/18 What problems and hazards can soft ground cause to a loaded forklift? - Answer️️ - Sunk and stuck machine, tip over sideways Why are forklift operators generally regarded as 'safety-critical' workers? - Answer️️ - Their actions (with the machine) can have SIGNIFICANT CONSEQUENCES on themselves and others affected by their work If the operator has loaded the machine onto a transporter/trailer on behalf of a driver, what checks must be carried out before they leave the cab? - Answer️️ -1. machine (i.e. boom, forks) are in the AGREED position 2. hydraulic operated components are grounded w