Test Bank Questions and Answers for Agricultural Engineering
A solvent recommended for removing grease and light rust is - Answers Varsol
A board with all 4 sides planed is specified by - Answers S4S
Placing a file at a 90 degree angle to the metal and pushing or pulling it is called - Answers Draw filing
Grain in lumber is caused by - Answers Annual rings
The wood removed by a saw blade leaves an opening called a - Answers Kerf
An example of a layout tool is a - Answers Outside calipers
Fire can be prevented by stopping or eliminating - Answers Combustible gases in the area
A green triangle on a fire extinguisher indicated that it can be - Answers Paper
SMV means - Answers Slow moving vehicle
Which of the following could be used to layout or measure and object? - Answers Try square
A bolt that has been rounded head over a square shoulder is - Answers Carriage bolt
A board foot is based on - Answers Cubic inches
Most farm incidents involve - Answers Machinery
Most portable drills have chuck sizes of - Answers 1/4, 3/8 and 1/2 inch
What size auger bit would be used to drill a 5/8 inch hole? - Answers 10
Which tool could be described as flat, course, or double cut? - Answers File
The plane small enough to hold in your hand is the - Answers Block
A bit brace uses - Answers Auger, expansive, and screwdriver bit
The length of time that a person is exposed to sound is called - Answers Duration
When measuring in the Ag shop, the shortest line on the ruler represents - Answers 1/16th inch
The number "8" on a wood screw represents - Answers The diameter
The lowercase letter "d" is used to designate the sizes of - Answers Nails
Which tool would be used to measure the inside diameter of a pipe? - Answers Calipers
Turning the first wrap of a power tool tightly around a tool can cause - Answers The insulation cord to
break
, A board foot is based on - Answers Number of cubic inches
A class D fire indicates which item is burning? - Answers Metal
After water touches an unprotected steel surface, rusting starts within - Answers Hours
A common problem with wooden handles is - Answers Splitting
Rough lumber is usually sold by the - Answers BF
The tool used to push the nail head below the surface of wood is a nail - Answers set
When using power tools, electrical shock hazards may be reduce by wearing - Answers rubber-soled
shoes
Safety glasses should have what proper logo on them? - Answers Z87.1
Tools are classified by - Answers Use
Hammers are considered what type of tool? - Answers Driving
What type of saw is used to cut with the grain? - Answers Rip saw
The use of hand tools is - Answers The foundation of mechanics
The back saw gets its name from - Answers Stiff back
How many sides are on a hexagon nut? - Answers 6
Oily rags in the shop should be stored in - Answers metal can
Orange as a safety color indicates - Answers Warning
The 3 parts of the fire triangle are - Answers Oxygen, heat, fuel
Which type of hardware may be described as 8d bright common? - Answers Nails
What number auger bit will drill a 1/2" hole? - Answers 8
How many safety colors are used in the shop? - Answers 9
What is the difference between a bolt and a screw? - Answers A bolt has a nut
What type of fire extinguisher is used for ordinary combustibles? - Answers class A
Hearing damage may occur of excessively exposed to noise at what level? - Answers 90 decibels
Wrenches are classified as - Answers Turning tools
How are all tools generally classified? - Answers By use
A solvent recommended for removing grease and light rust is - Answers Varsol
A board with all 4 sides planed is specified by - Answers S4S
Placing a file at a 90 degree angle to the metal and pushing or pulling it is called - Answers Draw filing
Grain in lumber is caused by - Answers Annual rings
The wood removed by a saw blade leaves an opening called a - Answers Kerf
An example of a layout tool is a - Answers Outside calipers
Fire can be prevented by stopping or eliminating - Answers Combustible gases in the area
A green triangle on a fire extinguisher indicated that it can be - Answers Paper
SMV means - Answers Slow moving vehicle
Which of the following could be used to layout or measure and object? - Answers Try square
A bolt that has been rounded head over a square shoulder is - Answers Carriage bolt
A board foot is based on - Answers Cubic inches
Most farm incidents involve - Answers Machinery
Most portable drills have chuck sizes of - Answers 1/4, 3/8 and 1/2 inch
What size auger bit would be used to drill a 5/8 inch hole? - Answers 10
Which tool could be described as flat, course, or double cut? - Answers File
The plane small enough to hold in your hand is the - Answers Block
A bit brace uses - Answers Auger, expansive, and screwdriver bit
The length of time that a person is exposed to sound is called - Answers Duration
When measuring in the Ag shop, the shortest line on the ruler represents - Answers 1/16th inch
The number "8" on a wood screw represents - Answers The diameter
The lowercase letter "d" is used to designate the sizes of - Answers Nails
Which tool would be used to measure the inside diameter of a pipe? - Answers Calipers
Turning the first wrap of a power tool tightly around a tool can cause - Answers The insulation cord to
break
, A board foot is based on - Answers Number of cubic inches
A class D fire indicates which item is burning? - Answers Metal
After water touches an unprotected steel surface, rusting starts within - Answers Hours
A common problem with wooden handles is - Answers Splitting
Rough lumber is usually sold by the - Answers BF
The tool used to push the nail head below the surface of wood is a nail - Answers set
When using power tools, electrical shock hazards may be reduce by wearing - Answers rubber-soled
shoes
Safety glasses should have what proper logo on them? - Answers Z87.1
Tools are classified by - Answers Use
Hammers are considered what type of tool? - Answers Driving
What type of saw is used to cut with the grain? - Answers Rip saw
The use of hand tools is - Answers The foundation of mechanics
The back saw gets its name from - Answers Stiff back
How many sides are on a hexagon nut? - Answers 6
Oily rags in the shop should be stored in - Answers metal can
Orange as a safety color indicates - Answers Warning
The 3 parts of the fire triangle are - Answers Oxygen, heat, fuel
Which type of hardware may be described as 8d bright common? - Answers Nails
What number auger bit will drill a 1/2" hole? - Answers 8
How many safety colors are used in the shop? - Answers 9
What is the difference between a bolt and a screw? - Answers A bolt has a nut
What type of fire extinguisher is used for ordinary combustibles? - Answers class A
Hearing damage may occur of excessively exposed to noise at what level? - Answers 90 decibels
Wrenches are classified as - Answers Turning tools
How are all tools generally classified? - Answers By use
