NWSA TTT-2
Can the WLL of a rigging system ever be exceeded? - No.
How is an exothermic weld performed? - By an oxyacetylene torch
How long after welding is completed does a spotter have to monitor a site for fires? - 1 hour.
How many grounds should be placed on a 425 foot coax cable? - 3.
How many transits are needed for a 3 leg guy tower? - 2 at 90 degrees.
How much galvanization should be removed while preparing for a weld? - 100%.
How much MPE is allowed before you start time averaging? - 100% MPE
If a Crane has a WLL of 6000 lbs and the headache ball is 300 lbs, what does that make the WLL? - 5,700 lbs.
What do you do if a synthetic sling has been burned? - Remove from service.
What is a structural member of a monopole? - Base Flange
What is the class plan for demolishing a tower? - Class IV
What is the fall protection latch mechanism load-rating? - 3,600 lbs
What is the load of 3 people tied off to a single point? - 15,000 lbs
What is tool used on Microwave Installs - Microwave flare tool.
What is used to secure DIN connectors? - Torque Wrench
What rigging plan is required for addition or removal for a 200 lb. appurtenance? - Class II
What type of radiation has a cumulative affect over time on the human body? - Ionizing
When crane boom is at 45 degrees, what will happen if you signal boom up? (this is one of the picture questions) -
The load will raise and the radius will be reduced.
When crane boom is at 45 degrees, what will happen if you signal cable up? (this is one of the picture questions) -
The load will raise.
When is a High-Visibility Vest required? - When in a public easement.
When is it acceptable to tie a knot in a sling to make is shorter? - Never.
When is it okay to modify a harness? - Never.
Which is not a method to test guy wire tension? - Turnbuckle.
Which is used for performance testing fiber optic cable? - OTDR
Which of the options will not prevent a fire while welding in a fire prone area? - Chipping Slag.
Can the WLL of a rigging system ever be exceeded? - No.
How is an exothermic weld performed? - By an oxyacetylene torch
How long after welding is completed does a spotter have to monitor a site for fires? - 1 hour.
How many grounds should be placed on a 425 foot coax cable? - 3.
How many transits are needed for a 3 leg guy tower? - 2 at 90 degrees.
How much galvanization should be removed while preparing for a weld? - 100%.
How much MPE is allowed before you start time averaging? - 100% MPE
If a Crane has a WLL of 6000 lbs and the headache ball is 300 lbs, what does that make the WLL? - 5,700 lbs.
What do you do if a synthetic sling has been burned? - Remove from service.
What is a structural member of a monopole? - Base Flange
What is the class plan for demolishing a tower? - Class IV
What is the fall protection latch mechanism load-rating? - 3,600 lbs
What is the load of 3 people tied off to a single point? - 15,000 lbs
What is tool used on Microwave Installs - Microwave flare tool.
What is used to secure DIN connectors? - Torque Wrench
What rigging plan is required for addition or removal for a 200 lb. appurtenance? - Class II
What type of radiation has a cumulative affect over time on the human body? - Ionizing
When crane boom is at 45 degrees, what will happen if you signal boom up? (this is one of the picture questions) -
The load will raise and the radius will be reduced.
When crane boom is at 45 degrees, what will happen if you signal cable up? (this is one of the picture questions) -
The load will raise.
When is a High-Visibility Vest required? - When in a public easement.
When is it acceptable to tie a knot in a sling to make is shorter? - Never.
When is it okay to modify a harness? - Never.
Which is not a method to test guy wire tension? - Turnbuckle.
Which is used for performance testing fiber optic cable? - OTDR
Which of the options will not prevent a fire while welding in a fire prone area? - Chipping Slag.
