Railroad Exam Questions With 100%
Verified Solutions
Over CORRECT ANSWERS If you are expecting a response you would end your
transmission with what?
Block CORRECT ANSWERS A length of track of defined limits on which train
movements are governed by signals or mandatory directives is known as what?
Restricted Speed CORRECT ANSWERS If you are operating a train from other than the
leading end and you are not equipped with an emergency brake valve and a whistle of
horn how must you proceed?
50 feet CORRECT ANSWERS What is standard car length when used to give the
Engineer distances?
Train Consist CORRECT ANSWERS Which document provides details about the cars
in your train?
A mandatory directives CORRECT ANSWERS which of the following radio signals must
be repeated?
2 miles CORRECT ANSWERS At a speed restriction you are required to remind the
Engineer how many miles in advance?
Class 1 CORRECT ANSWERS Where a train is originally assembled what type of brake
test is required?
Emergency CORRECT ANSWERS What kind of application is caused by a rapid
reduction of brake pipe pressure?
Restricted Speed CORRECT ANSWERS Return movements can be made at what
speed?
Three Step Protection CORRECT ANSWERS What protection is needed for a train
crew member to reset an EOTD on his/her train
CORRECT ANSWERS Which speed is not exceeding 40 mph
At a restricted speed CORRECT ANSWERS A train you are about to pass has had an
emergency brake application how should you proceed passed the train?
Medium speed CORRECT ANSWERS Which speed is not exceeding 30 mph
, 90 CORRECT ANSWERS Accuracy of a hand held gauge air gauge must be verified at
least once every how many days?
10 mph CORRECT ANSWERS Your train has a car with a 3 inch flat spot. At what
speed can you proceed?
B end CORRECT ANSWERS On which end of a freight car is the hand brake located?
Brake Pipe CORRECT ANSWERS What pipe carries air pressure to all cars in the
train?
apply CORRECT ANSWERS A reduction in brake pipe pressure will cause the brakes
to
2 plus effecient amount CORRECT ANSWERS You are going to leave 10 cars standing
unattached from the locomotive how many hand brakes need to be applied?
300 CORRECT ANSWERS How far from crossing does standing equipment have to be
left?
Cannot tell them CORRECT ANSWERS What is the preferred method to tell another
crew what signal the have?
Fouling CORRECT ANSWERS The placement of an individual in a position that could
be struck by equipment is known as what?
225 feet CORRECT ANSWERS On a yard track where there are no protective devices,
how far from the switch point must standing equipment be placed in order?
90 psi CORRECT ANSWERS What brake pipe pressure will be used for road freight
trains?
Exhaust position CORRECT ANSWERS What is the normal position of the retainer
valve
20 psi CORRECT ANSWERS When performing a Class 1 brake test the brakes on
each car mus apply in response to a what brake psi?
Window seat on lead locomotive CORRECT ANSWERS Where should conductor place
themselves on the train?
2 miles CORRECT ANSWERS At a speed restriction you are required to remind the
engineer how many miles in advance?
Verified Solutions
Over CORRECT ANSWERS If you are expecting a response you would end your
transmission with what?
Block CORRECT ANSWERS A length of track of defined limits on which train
movements are governed by signals or mandatory directives is known as what?
Restricted Speed CORRECT ANSWERS If you are operating a train from other than the
leading end and you are not equipped with an emergency brake valve and a whistle of
horn how must you proceed?
50 feet CORRECT ANSWERS What is standard car length when used to give the
Engineer distances?
Train Consist CORRECT ANSWERS Which document provides details about the cars
in your train?
A mandatory directives CORRECT ANSWERS which of the following radio signals must
be repeated?
2 miles CORRECT ANSWERS At a speed restriction you are required to remind the
Engineer how many miles in advance?
Class 1 CORRECT ANSWERS Where a train is originally assembled what type of brake
test is required?
Emergency CORRECT ANSWERS What kind of application is caused by a rapid
reduction of brake pipe pressure?
Restricted Speed CORRECT ANSWERS Return movements can be made at what
speed?
Three Step Protection CORRECT ANSWERS What protection is needed for a train
crew member to reset an EOTD on his/her train
CORRECT ANSWERS Which speed is not exceeding 40 mph
At a restricted speed CORRECT ANSWERS A train you are about to pass has had an
emergency brake application how should you proceed passed the train?
Medium speed CORRECT ANSWERS Which speed is not exceeding 30 mph
, 90 CORRECT ANSWERS Accuracy of a hand held gauge air gauge must be verified at
least once every how many days?
10 mph CORRECT ANSWERS Your train has a car with a 3 inch flat spot. At what
speed can you proceed?
B end CORRECT ANSWERS On which end of a freight car is the hand brake located?
Brake Pipe CORRECT ANSWERS What pipe carries air pressure to all cars in the
train?
apply CORRECT ANSWERS A reduction in brake pipe pressure will cause the brakes
to
2 plus effecient amount CORRECT ANSWERS You are going to leave 10 cars standing
unattached from the locomotive how many hand brakes need to be applied?
300 CORRECT ANSWERS How far from crossing does standing equipment have to be
left?
Cannot tell them CORRECT ANSWERS What is the preferred method to tell another
crew what signal the have?
Fouling CORRECT ANSWERS The placement of an individual in a position that could
be struck by equipment is known as what?
225 feet CORRECT ANSWERS On a yard track where there are no protective devices,
how far from the switch point must standing equipment be placed in order?
90 psi CORRECT ANSWERS What brake pipe pressure will be used for road freight
trains?
Exhaust position CORRECT ANSWERS What is the normal position of the retainer
valve
20 psi CORRECT ANSWERS When performing a Class 1 brake test the brakes on
each car mus apply in response to a what brake psi?
Window seat on lead locomotive CORRECT ANSWERS Where should conductor place
themselves on the train?
2 miles CORRECT ANSWERS At a speed restriction you are required to remind the
engineer how many miles in advance?
