BMW Associate level ASE test with
Questions and Correct Answers
Where can the CPO center operating manual be located?
BMW Warranties Documentation
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching
device.
Both A and B
Which button should be pressed for 5 seconds in order to update key for the key reader on
a F15 X5?
Lock Button
Regarding a display vehicle check on a 2019 2 series
Tech A says that the digital compass and clock need to be set/calibrated
Tech B says that you need to activate and verify optional series xm satellite radio (option 655)
Both A and B
New Vehicle Prep can be found under the main group:
Maintenance and general info
Warranty
After sales
Information Systems
, Maintenance and general info
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure
Brake pad thickness and tire thread depth
Tech A states that during a Quality Certification 1 on a G05 X5 it is necessary to press the
'AUTO' button in the light switch cluster.
Tech B states that during a Quality Certification 1 on a G05 X5 you can use the same QC1
inspection sheet as a G02.
Both A and B
If the vehicle is placed in transport mode and the vehicle battery voltage drops below 12
volts (approximately 30% State of Charge), the "Replace Battery" message will be displayed
in the instrument cluster.
Tech A says that charging the battery back to 100% State of Charge and clearing faults
will remove the message from the instrument cluster.
Tech B says that running Energy Diagnosis and clearing faults will remove the message
from the instrument cluster.
Neither A nor B
Transport Mode Switching Device can be used to successfully perform a QC1 inspection.
True or False?
False
Tech A states that on 2019 Quality Certification 1 the DOT (Department of Transportation)
numbers from each tire's sidewall do not need to be recorded for factory-fitted tires. The DOT
numbers were recorded at the manufacturing plant and stored in a proprietary database.
Tech B states that if a BMW-approved accessory wheel set is installed by the BMW center
prior to customer delivery, the DOT numbers from the accessory tires must be recorded on
an individually printed QC1 checklist.
Both A and B
Questions and Correct Answers
Where can the CPO center operating manual be located?
BMW Warranties Documentation
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching
device.
Both A and B
Which button should be pressed for 5 seconds in order to update key for the key reader on
a F15 X5?
Lock Button
Regarding a display vehicle check on a 2019 2 series
Tech A says that the digital compass and clock need to be set/calibrated
Tech B says that you need to activate and verify optional series xm satellite radio (option 655)
Both A and B
New Vehicle Prep can be found under the main group:
Maintenance and general info
Warranty
After sales
Information Systems
, Maintenance and general info
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure
Brake pad thickness and tire thread depth
Tech A states that during a Quality Certification 1 on a G05 X5 it is necessary to press the
'AUTO' button in the light switch cluster.
Tech B states that during a Quality Certification 1 on a G05 X5 you can use the same QC1
inspection sheet as a G02.
Both A and B
If the vehicle is placed in transport mode and the vehicle battery voltage drops below 12
volts (approximately 30% State of Charge), the "Replace Battery" message will be displayed
in the instrument cluster.
Tech A says that charging the battery back to 100% State of Charge and clearing faults
will remove the message from the instrument cluster.
Tech B says that running Energy Diagnosis and clearing faults will remove the message
from the instrument cluster.
Neither A nor B
Transport Mode Switching Device can be used to successfully perform a QC1 inspection.
True or False?
False
Tech A states that on 2019 Quality Certification 1 the DOT (Department of Transportation)
numbers from each tire's sidewall do not need to be recorded for factory-fitted tires. The DOT
numbers were recorded at the manufacturing plant and stored in a proprietary database.
Tech B states that if a BMW-approved accessory wheel set is installed by the BMW center
prior to customer delivery, the DOT numbers from the accessory tires must be recorded on
an individually printed QC1 checklist.
Both A and B
