Michigan State Brakes Certification
1) Most 1995 & newer vehicles use which of the following types of wheels
bearings on non-drive wheel?: Sealed non-serviceable
2) to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should:: drop slightly and remain firm
3) You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is:: Smaller and goes
towards the front of the car.
4) A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause:: a hard pedal feel requiring very high pedal effort to stop
5) A mechanic finds gear lube inside both rear brake drums on a rear
wheel drive vehicle. What is the most likely cause of this problem?: A
plugged axle 6. Which of the following incorrect service procedures will
cause brake lock-up?: master cylinder push rod adjusted too long
6) Which of the following describes the proper way to depressurized an
ABS system?: Pump the brake pedal at least 25 times (or more, depending
on the manufacturer's recommendation) with the ignition off.
, . Michigan State Brakes Certification
Study online at https://quizlet.com/_cezn7w
7) The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the:: technician use the parking
brake to adjust shoes and the cable is stuck
8) When turning brake drums:: use a dampening strap to reduce chatter
9) Which of the following is NOT a necessary drum brake measurement?:
run-out
10) On a 3-channel system, which wheels are on the same circuit?:
both rear wheels
11) One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter.: AC volts
12) The key input for the ABS control module comes from the:: wheel
speed sensors
13) ABS speed sensor and sensor rings:: should not be hammered or
tapped on and should always be replaced as a matched set
14) Flexible brake hoses should be replaced:: when dampness is evident
on the hose
15) Which of the following should be used to check for rotor thickness
variation:: Micrometer
1) Most 1995 & newer vehicles use which of the following types of wheels
bearings on non-drive wheel?: Sealed non-serviceable
2) to test a vacuum power brake booster in the vehicle, you should pump
the brake pedal at least 4 times, hold the brake pedal depressed, and
start the engine. the brake pedal should:: drop slightly and remain firm
3) You are installing a set of brake shoe linings that are not the same
length. Traditionally, the primary shoe lining is:: Smaller and goes
towards the front of the car.
4) A cracked or torn vacuum diaphragm in a brake power booster would
most likely cause:: a hard pedal feel requiring very high pedal effort to stop
5) A mechanic finds gear lube inside both rear brake drums on a rear
wheel drive vehicle. What is the most likely cause of this problem?: A
plugged axle 6. Which of the following incorrect service procedures will
cause brake lock-up?: master cylinder push rod adjusted too long
6) Which of the following describes the proper way to depressurized an
ABS system?: Pump the brake pedal at least 25 times (or more, depending
on the manufacturer's recommendation) with the ignition off.
, . Michigan State Brakes Certification
Study online at https://quizlet.com/_cezn7w
7) The rear brakes are dragging after having new linings installed and the
drums machined. the most likely cause is the:: technician use the parking
brake to adjust shoes and the cable is stuck
8) When turning brake drums:: use a dampening strap to reduce chatter
9) Which of the following is NOT a necessary drum brake measurement?:
run-out
10) On a 3-channel system, which wheels are on the same circuit?:
both rear wheels
11) One way to test an ABS wheel speed signal is to use _____ on your
digital multimeter.: AC volts
12) The key input for the ABS control module comes from the:: wheel
speed sensors
13) ABS speed sensor and sensor rings:: should not be hammered or
tapped on and should always be replaced as a matched set
14) Flexible brake hoses should be replaced:: when dampness is evident
on the hose
15) Which of the following should be used to check for rotor thickness
variation:: Micrometer
