bicsi
Elastomeric module is what type of firestop system? - correct answer-Mechanical
Which of the following is not part of an its installer function when working within a
designated work area? - correct answer-Leave access floor panels, open ceiling
systems, or trenches uncovered or open
The standard that covers commercial building grounding and bonding requirements
for telecommunications is: - correct answer-ANSI/TIA 607
The use of ___ reduces the risk of damage when attaching a bonding conductor to a
metallic conduit - correct answer-Grounding bushings
Commonly installed in a workspace, what individual network connects to two or more
devises through the use of wireless? - correct answer-Personal area network
What is the color code of pair 19 of a 25 pair cable? - correct answer-Yellow-Brown
There are three forms of transmission methods to move information in the form of
electrical or optical signals from one point to another through a transport medium.
What are the three? - correct answer-Simplex, half duplex and full duplex
What is the NEC article regulating communications systems? - correct answer-8
What is the number of required lanyards when leaving a lift? - correct answer-2
In testing your copper cabling, you get failing NEXT (near-end crosstalk) reports.
One of your steps to solve this problem should be: - correct answer-Check the
quality of the wire terminations in the connector
The ITS installer should always seek the guidance of the __, when coming onto any
project for the minimum requirements for safe work and employee health at work -
correct answer-AHJ
When bonding equipment racks to the PBB or SBB, what is the minimum size
ground wire you should use? - correct answer-6 AWG
Ohm's Law is represented by ohms (R), amperage (I), and voltage (V). What is the
formula for Ohm's Law? - correct answer-V=IXR
To avoid electromagnetic interference (EMI) on cabling, what is the recommended
minimum separation from electric motors and transformers? - correct answer-48"
, When terminating Cat5e and higher, pair untwisting cannot exceed ____. - correct
answer-0.5"
Who should have the responsibility of selecting the type of pokethough (devise used
for fire barriers) device to be used? - correct answer-ICT designer or structural
engineer
What is the color code of the 7th pair of a 25 pair cable? - correct
answer-Red-Orange
If existing cables do not meet the requirements of the category/class of cabling, they
must be; - correct answer-Replaced to meet new standards and or codes
A certification tester rated at a tester level IIIe Cat6a (class Ea) can test to a
bandwidth up to; - correct answer-500 MHz
Nothing impacts the design and construction of a telecommunications network more
than ___; - correct answer-Codes, standards and regulations
What serves the purpose of increasing personnel safety and reduces the likelihood
of fire hazards by serving as the path for fault current? - correct answer-Equipment
grounding system
When using cable management, care should be used to select management that
protects what? - correct answer-Minimum bend radius
NFPA 70, The National Electric Code, is revised every ____? - correct answer-3
years
The PPE that an in ITS installer is required to wear when performing a task depends
on each of the following except; - correct answer-When driving the company van on
a new construction job site
Its suggested that open top cable supports be used for no more than how many
cables? - correct answer-50
A common cabinet configuration providing increased efficiency in heat management
is where? - correct answer-The hot sides of two cabinet rows face each other
A digital signal is represented by two bits; zero and one. Zero represents an "off"
signal and one represents an "on" signal. Each signal is referenced in voltage. What
is the most commonly used "on" or "off" (or plus/minus) voltage within the digital
signal? - correct answer-3V
Elastomeric module is what type of firestop system? - correct answer-Mechanical
Which of the following is not part of an its installer function when working within a
designated work area? - correct answer-Leave access floor panels, open ceiling
systems, or trenches uncovered or open
The standard that covers commercial building grounding and bonding requirements
for telecommunications is: - correct answer-ANSI/TIA 607
The use of ___ reduces the risk of damage when attaching a bonding conductor to a
metallic conduit - correct answer-Grounding bushings
Commonly installed in a workspace, what individual network connects to two or more
devises through the use of wireless? - correct answer-Personal area network
What is the color code of pair 19 of a 25 pair cable? - correct answer-Yellow-Brown
There are three forms of transmission methods to move information in the form of
electrical or optical signals from one point to another through a transport medium.
What are the three? - correct answer-Simplex, half duplex and full duplex
What is the NEC article regulating communications systems? - correct answer-8
What is the number of required lanyards when leaving a lift? - correct answer-2
In testing your copper cabling, you get failing NEXT (near-end crosstalk) reports.
One of your steps to solve this problem should be: - correct answer-Check the
quality of the wire terminations in the connector
The ITS installer should always seek the guidance of the __, when coming onto any
project for the minimum requirements for safe work and employee health at work -
correct answer-AHJ
When bonding equipment racks to the PBB or SBB, what is the minimum size
ground wire you should use? - correct answer-6 AWG
Ohm's Law is represented by ohms (R), amperage (I), and voltage (V). What is the
formula for Ohm's Law? - correct answer-V=IXR
To avoid electromagnetic interference (EMI) on cabling, what is the recommended
minimum separation from electric motors and transformers? - correct answer-48"
, When terminating Cat5e and higher, pair untwisting cannot exceed ____. - correct
answer-0.5"
Who should have the responsibility of selecting the type of pokethough (devise used
for fire barriers) device to be used? - correct answer-ICT designer or structural
engineer
What is the color code of the 7th pair of a 25 pair cable? - correct
answer-Red-Orange
If existing cables do not meet the requirements of the category/class of cabling, they
must be; - correct answer-Replaced to meet new standards and or codes
A certification tester rated at a tester level IIIe Cat6a (class Ea) can test to a
bandwidth up to; - correct answer-500 MHz
Nothing impacts the design and construction of a telecommunications network more
than ___; - correct answer-Codes, standards and regulations
What serves the purpose of increasing personnel safety and reduces the likelihood
of fire hazards by serving as the path for fault current? - correct answer-Equipment
grounding system
When using cable management, care should be used to select management that
protects what? - correct answer-Minimum bend radius
NFPA 70, The National Electric Code, is revised every ____? - correct answer-3
years
The PPE that an in ITS installer is required to wear when performing a task depends
on each of the following except; - correct answer-When driving the company van on
a new construction job site
Its suggested that open top cable supports be used for no more than how many
cables? - correct answer-50
A common cabinet configuration providing increased efficiency in heat management
is where? - correct answer-The hot sides of two cabinet rows face each other
A digital signal is represented by two bits; zero and one. Zero represents an "off"
signal and one represents an "on" signal. Each signal is referenced in voltage. What
is the most commonly used "on" or "off" (or plus/minus) voltage within the digital
signal? - correct answer-3V
