ASE-STYLE REVIEW QUESTIONS
1. Technician A says that using a computer 4. Which of the following is/are listed on a repair
to generate a repair order can sometimes order?
save paper. Technician B says that a hard a. The concern c. The correction
copy of a repair order is needed for the b. The cause d. All of the above
customer, and often for the technician.
5. All of the following could be a source of irritation
Who is right?
to a customer except:
a. Technician A c. Both A and B
a. Grease on a fender
b. Technician B d. Neither A nor B
2. Technician A says that a repair order contains a b. Grease on the carpet or seat
written estimate of the cost of a repair. Technician c. Grease on the steering wheel
B says that a repair order lists a record of telephone d. Grease on a wheel bearing
conversations with the customer. Who is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
3. Technician A says that red shop towels turn
blue if they come into contact with battery acid.
Technician B says that shop clothing is often made
of materials that are resistant to battery acid. Who
is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
,ASE-STYLE REVIEW QUESTIONS
4. Which of the following is/are true about the VIN?
1. Technician A says that during disassembly,
reassemble brackets to a component for easier a. The eighth digit tells the year of the vehicle.
reassembly. Technician B says to take a digital b. The tenth digit tells the engine of the vehicle.
photo of a complicated component before c. Both A and B.
disassembling it. Who is right? d. Neither A nor B.
a. Technician A c. Both A and B 5. Technician A says that the flat rate is the amount of
b. Technician B d. Neither A nor B time it should take to complete a repair job. Tech-
2. Which of the following might be found on an nician B says that a flat-rate technician is paid for
underhood label? the time it actually takes to complete the job. Who
a. Engine size is right?
b. Vacuum hose routing a. Technician A c. Both A and B.
c. Supplied emission devices b. Technician B d. Neither A nor B.
d. All of the above
3. Step-by-step repair information is included in all of
the following except:
a. Mitchell On-Demand.
b. All-Data.
c. An owner’s manual.
d. None of the above.
,ASE-STYLE REVIEW QUESTIONS
1. One liter equals 4. A vernier caliper can measure
a. 1000 cubic centimeters. a. Inside diameter.
b. 1 quart. b. Outside diameter.
c. 1 gallon. c. Depth.
d. None of the above. d. All of the above.
2. Technician A says that one revolution of the 5. Technician A says that a gauge block is used to
micrometer thimble equals 1 40 inch. Technician B measure valve lash (clearance). Technician B says
says that one revolution of the micrometer thimble that the vernier scale on a micrometer measures to
equals 0.025 inch. Who is right? 0.001 in. Who is right?
a. Technician A c. Both A and B a. Technician A
b. Technician B d. Neither A nor B b. Technician B
3. The metric measuring system is based on
c. Both A and B
a. The gold standard.
d. Neither A nor B
b. The number 10.
c. Fractions of 1 64 in.
d. The distance between the earth and the moon.
, ASE-STYLE REVIEW QUESTIONS
1. Which of the following are methods by which twist 4. How many radial lines does an SAE grade 8 bolt
drill sizes are classified? have on its head?
a. Number c. Fraction a. 2
b. Letter d. All of the above b. 4
2. Technician A says that the “20” in 1 4 3 20 signifies c. 6
the total number of threads the fastener has. Tech- d. 8
nician B says that the “1 4” signifies the socket size of
5. Technician A says that a nonhardened nut loses
the fastener head. Who is right?
clamping ability each time it is retorqued. Techni-
a. Technician A c. Both A and B cian B says that a capscrew loses clamping ability
b. Technician B d. Neither A nor B each time it is retorqued. Who is right?
3. Technician A says that a hole can be drilled in cast a. Technician A c. Both A and B
iron using no lubricant. Technician B says that a b. Technician B d. Neither A nor B
hole can be drilled in aluminum using no lubricant.
Who is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
1. Technician A says that using a computer 4. Which of the following is/are listed on a repair
to generate a repair order can sometimes order?
save paper. Technician B says that a hard a. The concern c. The correction
copy of a repair order is needed for the b. The cause d. All of the above
customer, and often for the technician.
5. All of the following could be a source of irritation
Who is right?
to a customer except:
a. Technician A c. Both A and B
a. Grease on a fender
b. Technician B d. Neither A nor B
2. Technician A says that a repair order contains a b. Grease on the carpet or seat
written estimate of the cost of a repair. Technician c. Grease on the steering wheel
B says that a repair order lists a record of telephone d. Grease on a wheel bearing
conversations with the customer. Who is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
3. Technician A says that red shop towels turn
blue if they come into contact with battery acid.
Technician B says that shop clothing is often made
of materials that are resistant to battery acid. Who
is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
,ASE-STYLE REVIEW QUESTIONS
4. Which of the following is/are true about the VIN?
1. Technician A says that during disassembly,
reassemble brackets to a component for easier a. The eighth digit tells the year of the vehicle.
reassembly. Technician B says to take a digital b. The tenth digit tells the engine of the vehicle.
photo of a complicated component before c. Both A and B.
disassembling it. Who is right? d. Neither A nor B.
a. Technician A c. Both A and B 5. Technician A says that the flat rate is the amount of
b. Technician B d. Neither A nor B time it should take to complete a repair job. Tech-
2. Which of the following might be found on an nician B says that a flat-rate technician is paid for
underhood label? the time it actually takes to complete the job. Who
a. Engine size is right?
b. Vacuum hose routing a. Technician A c. Both A and B.
c. Supplied emission devices b. Technician B d. Neither A nor B.
d. All of the above
3. Step-by-step repair information is included in all of
the following except:
a. Mitchell On-Demand.
b. All-Data.
c. An owner’s manual.
d. None of the above.
,ASE-STYLE REVIEW QUESTIONS
1. One liter equals 4. A vernier caliper can measure
a. 1000 cubic centimeters. a. Inside diameter.
b. 1 quart. b. Outside diameter.
c. 1 gallon. c. Depth.
d. None of the above. d. All of the above.
2. Technician A says that one revolution of the 5. Technician A says that a gauge block is used to
micrometer thimble equals 1 40 inch. Technician B measure valve lash (clearance). Technician B says
says that one revolution of the micrometer thimble that the vernier scale on a micrometer measures to
equals 0.025 inch. Who is right? 0.001 in. Who is right?
a. Technician A c. Both A and B a. Technician A
b. Technician B d. Neither A nor B b. Technician B
3. The metric measuring system is based on
c. Both A and B
a. The gold standard.
d. Neither A nor B
b. The number 10.
c. Fractions of 1 64 in.
d. The distance between the earth and the moon.
, ASE-STYLE REVIEW QUESTIONS
1. Which of the following are methods by which twist 4. How many radial lines does an SAE grade 8 bolt
drill sizes are classified? have on its head?
a. Number c. Fraction a. 2
b. Letter d. All of the above b. 4
2. Technician A says that the “20” in 1 4 3 20 signifies c. 6
the total number of threads the fastener has. Tech- d. 8
nician B says that the “1 4” signifies the socket size of
5. Technician A says that a nonhardened nut loses
the fastener head. Who is right?
clamping ability each time it is retorqued. Techni-
a. Technician A c. Both A and B cian B says that a capscrew loses clamping ability
b. Technician B d. Neither A nor B each time it is retorqued. Who is right?
3. Technician A says that a hole can be drilled in cast a. Technician A c. Both A and B
iron using no lubricant. Technician B says that a b. Technician B d. Neither A nor B
hole can be drilled in aluminum using no lubricant.
Who is right?
a. Technician A c. Both A and B
b. Technician B d. Neither A nor B
