2024
Smartstudy.org
CIP LEVEL 1 NACE-CIP1-001
PRACTICE TEST QUESTIONS |
QUESTIONS WITH 100% CORRECT
ANSWERS | VERIFIED
This document is meant to help students
pass exams with good grades
.
,1. What is the Inspector's responsibility when it comes to safety on a project?
ANSWER :
Safety enforcement is not the responsibility of the inspector; however, it is
his/her
responsibility to report any issues that may affect the project.
2. The Inspector's checklist for surface preparation should include
ANSWER :
ambient conditions, conditions of substrate, pre-blast surface cleanliness,
shot/grit
size selection, shot/grit cleanliness, abrasive blasting equipment, surface
profile,
surface cleanliness after abrasive blasting, operator qualifications, safety
3. If inspection is to be effective with regards to soluble salts, the specification should
very clearly state
ANSWER :
limits to be accepted, specific salts to be limited, test method to be used,
frequency of testing, locations in which tests should be administered
4. Three test methods for surface profile include
ANSWER :
Comparator and coupons
Replica tape
Digital surface profile gauge
5. Depth of surface profile can be evaluated by several methods
ANSWER :
ISO Comparator
Replica Tape
Digital Profile Gauge
6. The ISO Comparator grades may be recorded
ANSWER :
Finer-than-fine grade, fine grade, medium grade, coarse grade, coarser than
coarse grade
7. Name some test that may need to be conducted during surface preparation and
coating operations.
ANSWER :
Temperature, Relative Humidity, Dew Point, Anchor Profile, Surface
Cleanliness
, 8. Name some of the documentation/reports that may be required to be maintained on
a coatings project.
ANSWER :
Daily, Weekly Summary, Materials Usage Report, Manpower and
Equipment,
Non-Conformance, and Conformance.
9. What are the most important characteristics of a good report?
ANSWER :
Objective, Accurate, and Detailed.
10. What is the Inspector's primary responsibility and what should the Inspector not do
as it pertains to the specifications.
ANSWER :
The Inspector's primary responsibility as the Inspector is to "enforce" the
specification. The inspector is NOT to make any changes to the
specification for
any reason.
11. Industrial and marine coatings are commonly referred to by
ANSWER :
Generic resin type
12. Oil based coatings applied over alkaline surfaces may result in
ANSWER :
Saponification
13. Three (3) types of water-blasting include
ANSWER :
• Grit blasting with a shroud
• Sand injected water blast
• Slurry blast with grit/water mix
14. The NACE/SSPC Waterjetting Standard is
ANSWER :
SSPC/VIS 4 and VIS 7 are visual comparators to be used with the standard.
15. In aspects to coating inspection, what are Ultraviolet lights used to detect?
ANSWER :
Hydrocarbon contaminants, such as OIL AND GREASE
16. What is the inspectors primary responsibility and what should the Inspector not do
as it pertains to the specification.
ANSWER :
Smartstudy.org
CIP LEVEL 1 NACE-CIP1-001
PRACTICE TEST QUESTIONS |
QUESTIONS WITH 100% CORRECT
ANSWERS | VERIFIED
This document is meant to help students
pass exams with good grades
.
,1. What is the Inspector's responsibility when it comes to safety on a project?
ANSWER :
Safety enforcement is not the responsibility of the inspector; however, it is
his/her
responsibility to report any issues that may affect the project.
2. The Inspector's checklist for surface preparation should include
ANSWER :
ambient conditions, conditions of substrate, pre-blast surface cleanliness,
shot/grit
size selection, shot/grit cleanliness, abrasive blasting equipment, surface
profile,
surface cleanliness after abrasive blasting, operator qualifications, safety
3. If inspection is to be effective with regards to soluble salts, the specification should
very clearly state
ANSWER :
limits to be accepted, specific salts to be limited, test method to be used,
frequency of testing, locations in which tests should be administered
4. Three test methods for surface profile include
ANSWER :
Comparator and coupons
Replica tape
Digital surface profile gauge
5. Depth of surface profile can be evaluated by several methods
ANSWER :
ISO Comparator
Replica Tape
Digital Profile Gauge
6. The ISO Comparator grades may be recorded
ANSWER :
Finer-than-fine grade, fine grade, medium grade, coarse grade, coarser than
coarse grade
7. Name some test that may need to be conducted during surface preparation and
coating operations.
ANSWER :
Temperature, Relative Humidity, Dew Point, Anchor Profile, Surface
Cleanliness
, 8. Name some of the documentation/reports that may be required to be maintained on
a coatings project.
ANSWER :
Daily, Weekly Summary, Materials Usage Report, Manpower and
Equipment,
Non-Conformance, and Conformance.
9. What are the most important characteristics of a good report?
ANSWER :
Objective, Accurate, and Detailed.
10. What is the Inspector's primary responsibility and what should the Inspector not do
as it pertains to the specifications.
ANSWER :
The Inspector's primary responsibility as the Inspector is to "enforce" the
specification. The inspector is NOT to make any changes to the
specification for
any reason.
11. Industrial and marine coatings are commonly referred to by
ANSWER :
Generic resin type
12. Oil based coatings applied over alkaline surfaces may result in
ANSWER :
Saponification
13. Three (3) types of water-blasting include
ANSWER :
• Grit blasting with a shroud
• Sand injected water blast
• Slurry blast with grit/water mix
14. The NACE/SSPC Waterjetting Standard is
ANSWER :
SSPC/VIS 4 and VIS 7 are visual comparators to be used with the standard.
15. In aspects to coating inspection, what are Ultraviolet lights used to detect?
ANSWER :
Hydrocarbon contaminants, such as OIL AND GREASE
16. What is the inspectors primary responsibility and what should the Inspector not do
as it pertains to the specification.
ANSWER :
