ASQ CQT Certification Exam Sample Questions with Complete Solutions

ASQ CQT Certification Exam Sample Questions with Complete Solutions Start your Preparation for ASQ CQT and become ASQ Certified Quality Technician certified with ProcessE. Here you get online practice tests prepared and approved by ASQ certified experts based on their own certification exam experience. Here, you also get the detailed and regularly updated syllabus for ASQ CQT. ASQ CQT practice tests provided by the ProcessE is just one of the promising techniques of preparation for the CQT exam. This ASQ Certified Quality Technician practice tests are composed by a team of experienced professionals. Upgraded Quality Technician practice questions will give you the useful experience of learning for the ASQ CQT exam. You can gain the ASQ Certified Quality Technician (CQT) certification on the first go with the help of the CQT practice questions. Getting that ASQ CQT certification is a great first step and these practice tests can help you toward a better score. Millions of aspirants have become certified with our practice tests. Give your preparation a new edge with ProcessE practice tests. If you are planning to prepare for CQT exam, but not sure how hard the exam is and you want to try out a sample test, you can take our CQT practice test. To help you assess your readiness, we've developed a set of ASQ CQT sample questions and assembled them into a free online test exam. Online Practice Test: Study Guide for Quality Technician CQT Certification Click Here... CQT Study Guide to Crack ASQ Quality Technician Certification Click Here... Question: 01. Who is responsible for determining whether a follow-up response is sufficient to close out an internal audit? a) Executive management b) The quality manager c) The audit team leader d) The internal auditee Answer: c) The audit team leader Question: 02. The reduction or elimination of incoming inspection stations should be considered only when a) evidence of supplier process control techniques is provided for the material used b) evidence of a high defect rate is present in the manufacturing operation c) the next process step will mask defects d) it is cost-prohibitive to the supplier to test the parts Answer: a) evidence of supplier process control techniques is provided for the material used Question: 03. Which of the following elements of an audit program must be aligned with the organization's overall strategy? a) Objectives b) Schedule c) Scope d) Compliance Answer: a) Objectives Question: 04. If a distribution is normal, with μ = 50 and σ = 15, what percentage of data will be less than 30? a) 59.18% b) 40.82% c) 1.33% d) 9.18% Answer: d) 9.18% Question: 05. Which of the following tools would be best for measuring projected surface intersections? a) Thread micrometer b) Optical comparator c) Profilometer d) Protractor Answer: b) Optical comparator Question: 06. Under which of the following circumstances can the calibration interval of a gage be lengthened? a) No defective parts were produced that were checked with the gage. b) The production rate of the parts checked with the gage increases. c) The inspection department requests the change in writing. d) History indicates satisfactory calibration performance. Answer: d) History indicates satisfactory calibration performance. Question: 07. When applied to size features such as hole and shaft diameters, MMC refers to a) maximum shaft diameter, maximum hole diameter b) minimum shaft diameter, minimum hole diameter c) maximum shaft diameter, minimum hole diameter d) minimum shaft diameter, maximum hole diameter Answer: c) maximum shaft diameter, minimum hole diameter Question: 08. Which of the following groups is responsible for producing parts to specifications? a) The quality assurance department b) The manufacturing department c) The process engineering department d) The manufacturing engineering department Answer: b) The manufacturing department Question: 09. A material review board (MRB) usually has the responsibility for which of the following? a) Analyzing and dispositioning of nonconforming material b) Defining the statistical specifications of nonconforming material c) Assuring the availability of materials to meet production schedules d) Controlling the cost of materials Answer: a) Analyzing and dispositioning of nonconforming material Question: 10. What is the recommended minimum number of subgroups necessary to calculate the limits for a control chart? a) 10 b) 15 c) 25 d) 35 Answer: c) 25