• Wrong document? Swap it for free
  • Written by students who passed
  • Immediately available after payment
  • Read online or as PDF
Sell
Where do you study
Your language
Document preview thumbnail
Preview 2 out of 15 pages
Exam (elaborations)

MEC322 - Midterm Study Guide - Latest Edition Updated

Document preview thumbnail
Preview 2 out of 15 pages

MEC322 - Midterm Study Guide - Latest Edition Updated What is Metrology? - answer - The science of measurement. It includes all theoretical and practical aspects of measurement. What are Dimensions? - answer - Linear or Angular sizes of a component specified on the part drawing What are tolerances? - answer - Allowable variations/permissible error from the specified part dimensions that are permitted in manufacturing. Can be by an amount or percentage. What do you call a tolerance in both the positive and negative direction? - answer - Bilateral Tolerance What is the definition of accuracy? - answer - How closely a measured value is to an accepted value (target) What is the definition of precision? - answer - How close a series of measurements are to each other What is the definition of circularity? - answer - Circularity of an object, also known as roundness What is the definition of concentricity? - answer - In geometry, two or more objects are said to be concentric, coaxal, or coaxial when they share the same center or axis. What is the definition of cylindricity? - answer - Cylindricity is a 3-Dimensional tolerance that controls the overall form of a cylindrical feature to ensure that it is round enough and straight enough along its axis. In inspection, which procedure provides more information? Gaging or Measuring? - answer - Measuring What is the definition of Gaging? - answer - Using a fixed tool/standard to determine a tool's measurements min/max. What material is a surface plate usually made of? - answer - Granite What is a graduated measuring device? - answer - Any device with markings for measures of length An outside micrometer is appropriate for measuring which of the following (two correct answers): (a) hole depth, (b) hole diameter, (c) part length, (d) shaft diameter (e) surface roughness - answer - (c) and (d) In a GO/NO-GO gage, which one of the following best describes the function of the GO gage? - answer - Checks the minimum size (minimum permissible dimension) What are two types of GO-NO GO Gauges? - answer - Snap Gauge (Clamp Shaped) and Plug Gauge (double ended), Limit Gauge Surface texture includes which of the following characteristics of a surface? - answer - 1) Deviations from the nominal surface, 2) Feed marks of the tool that produced the surface, 3) Surface Cracks Surface texture is included within the scope of surface integrity? True or False - answer - True Surface roughness can be measured as either an arithmetic average (AA) or a root-mean square (RMS) average. Which value is almost always greater for most surfaces? - answer - Root-mean square is always more favorable. Thermal energy is normally associated with which of the following changes in the altered layer? - answer - Hardness Variations Heat Affected Zone Recrystallization Which manufacturing process is likely to result in the best surface finish out of the ones listed below? (a) arc welding, (b) grinding, (c) machining, (d) sand casting, or (e) sawing - answer - (b) Grinding Which one of the following manufacturing processes is likely to result in the worst surface finish: (a) cold rolling, (b) grinding, (c) machining, (d) sand casting, or (e) sawing? - answer - Sand Casting What are the three different types of fits? - answer - Clearance Fit, Transition fit, Interference fit When referring to a shaft going into a hole, what would a clearance fit indicate? - answer - Indicates that the dimensions must be able to go into (clear) the shaft and thus the tolerances mus be at or below the shaft's tolerance. When referring to a shaft going into a hole, what would a transition fit indicate? - answer - Indicates that the dimension must be very similar or the same as the shaft. When referring to a shaft going into a hole, what would a interference fit indicate? - answer - Indicate that the dimension must be a little bit bigger than the shaft, and thus interfere with the hole. Nominal Surface - answer - designer's


Document information

Uploaded on
November 20, 2026
Number of pages
15
Written in
2026/2027
Type
Exam (elaborations)
Contains
Questions & answers
$13.99

Wrong document? Swap it for free Within 14 days of purchase and before downloading, you can choose a different document. You can simply spend the amount again.
Written by students who passed
Immediately available after payment
Read online or as PDF

Seller avatar
Reputation scores are based on the amount of documents a seller has sold for a fee and the reviews they have received for those documents. There are three levels: Bronze, Silver and Gold. The better the reputation, the more your can rely on the quality of the sellers work.
SARAHnkalu
4.6
(7)
Sold
49
Followers
0
Items
7968
Last sold
1 day ago



Why students choose Stuvia

Created by fellow students, verified by reviews

Quality you can trust: written by students who passed their tests and reviewed by others who've used these notes.

Didn't get what you expected? Choose another document

No worries! You can instantly pick a different document that better fits what you're looking for.

Pay as you like, start learning right away

No subscription, no commitments. Pay the way you're used to via credit card and download your PDF document instantly.

Student with book image

“Bought, downloaded, and aced it. It really can be that simple.”

Alisha Student

Working on your references?

Create accurate citations in APA, MLA and Harvard with our free citation generator.

Working on your references?

Frequently asked questions

Whoops! We can’t load your doc right now. Try again or contact support.