QUESTIONS AND CORRECT ANSWERS (VERIFIED
ANSWERS) Q&A 2027 |INSTANT DOWNLOAD PDF
1. Which of the following best describes the primary purpose
of structural engineering?
A. To improve the appearance of buildings B. To ensure
structures safely resist applied loads C. To reduce interior
maintenance costs D. To select decorative materials
Correct answer: B. To ensure structures safely resist applied
loads
Rationale: Structural engineering focuses on designing
structures that safely carry loads while meeting strength,
stability, serviceability, and durability requirements.
2. Which type of load is generally considered a permanent
load on a building?
A. Occupant load B. Wind load C. Dead load D. Snow load
Correct answer: C. Dead load
Rationale: Dead loads include the weight of permanent
structural components and other fixed building elements.
3. What is the SI unit of stress?
A. Newton B. Pascal C. Joule D. Watt
,Correct answer: B. Pascal
Rationale: Stress is force divided by area. One pascal equals one
newton per square meter.
4. Which structural element primarily resists axial
compression in a typical building frame?
A. Column B. Curtain wall C. Window frame D. Expansion joint
Correct answer: A. Column
Rationale: Columns commonly transfer vertical loads from
beams and floors to the foundation, primarily through axial
compression.
5. What is the principal function of a beam?
A. To transfer loads primarily through bending and shear B. To
prevent all building movement C. To eliminate foundation
settlement D. To resist only torsion
Correct answer: A. To transfer loads primarily through bending
and shear
Rationale: Beams support transverse loads and transfer them
to columns, walls, or other supporting elements.
6. What does Young’s modulus measure?
A. Material density B. Material stiffness in the elastic range C.
Ultimate material weight D. Thermal expansion only
Correct answer: B. Material stiffness in the elastic range
,Rationale: Young’s modulus is the ratio of normal stress to
normal strain within the linear-elastic range.
7. Which equation defines normal stress under a uniform axial
force?
A. σ=P/Aσ=P/A B. σ=PLσ=PL C. σ=A/Pσ=A/P D. σ=P+Aσ=P+A
Correct answer: A. σ=P/Aσ=P/A
Rationale: Normal stress is the applied axial force divided by
the cross-sectional area, assuming a uniform distribution.
8. What is the primary cause of bending stress in a beam?
A. A change in temperature only B. A bending moment C. A
uniform axial force only D. A support reaction without internal
action
Correct answer: B. A bending moment
Rationale: Bending moments create tensile and compressive
normal stresses across a beam’s cross section.
9. In a simply supported beam carrying a uniformly distributed
load, where is the maximum positive bending moment
generally located?
A. At the left support B. At the right support C. Near midspan D.
Outside the beam
Correct answer: C. Near midspan
, Rationale: For a symmetric, simply supported beam with a
uniform load over its full span, the maximum positive bending
moment occurs at midspan.
10. What is the bending moment at an ideal simple support
when no external couple is applied at the support?
A. Equal to the maximum span moment B. Zero C. Equal to the
total load D. Always negative
Correct answer: B. Zero
Rationale: An ideal pin or roller support does not resist a
bending couple, so the bending moment at that support is zero.
11. Which condition is necessary for static equilibrium of a
planar structure?
A. The sum of horizontal forces must be positive B. The sum of
vertical forces must be negative C. The sums of horizontal
forces, vertical forces, and moments must be zero D. All
reactions must be equal
Correct answer: C. The sums of horizontal forces, vertical forces,
and moments must be zero
Rationale: A planar body in static equilibrium satisfies ∑Fx=0∑Fx
=0, ∑Fy=0∑Fy=0, and ∑M=0∑M=0.
12. What is the main purpose of a factor of safety?
A. To eliminate the need for engineering calculations B. To
provide a margin against uncertainty and failure C. To
guarantee zero deformation D. To reduce all loads to zero