PDCA Craftsperson
Certification
Examination Exam
,PDCA Craftsperson Certification Examination Exam
Question 1
Which focus best brings together these responsibilities: “Quality control inspection criteria during
execution and upon completion” and “jobsite cleanup”?
A. Power tool operation, safety, and troubleshooting
B. Quality Control, Planning, and Job Standards
C. Safety and Regulations
D. Tools and Equipment
Correct Answer: B
Full Explanation:
Both responsibilities are part of Quality Control, Planning, and Job Standards: Quality control
inspection criteria during execution and upon completion, and jobsite cleanup. Their common
technical focus is the reason this choice fits the pair. A different focus would not preserve this
specific grouping of responsibilities.
Question 2
Which technical focus most directly encompasses “dew point”?
A. Safety and Regulations
B. Power tool operation, safety, and troubleshooting
C. Tools and Equipment
D. Environmental limitations
Correct Answer: D
Full Explanation:
dew point is an aspect of Environmental limitations. This choice preserves the specific relationship
between the responsibility and its technical focus. The other choices identify separate focuses,
rather than the direct category of the activity described.
Question 3
A team roster assigns one person to “Airless and conventional paint spray equipment setup,
operation, cleaning, and safety” and another to “Equipment calibration, maintenance schedules, and
storage practices”. No completed work or review results are recorded. Which statement stays within
the roster’s evidentiary value?
A. Assigning two people proves that their work has been independently verified.
B. Both responsibilities are complete because named owners appear beside them.
C. Neither person is responsible until a passing result has already been obtained.
D. Responsibility has been assigned; execution and results are not established by the roster.
Correct Answer: D
Full Explanation:
The roster establishes ownership of the responsibilities for “Airless and conventional paint spray
equipment setup, operation, cleaning, and safety” and “Equipment calibration, maintenance
schedules, and storage practices”. Assignment, completion, and verification are separate states. A
named owner is not evidence that the assigned work has been carried out or that its result has
been accepted.
5521 Page 2
,PDCA Craftsperson Certification Examination Exam
Question 4
A discussion is limited to identifying issues concerning “Specialty coatings, textured finishes, and
decorative application procedures”; selecting corrective measures for “Materials and Science” is
expressly outside its assignment. Which deliverable best respects that boundary?
A. An issue-identification discussion within the assigned subject, without claiming the excluded
corrective work.
B. A claim that corrective measures are approved merely because issues were identified.
C. A replacement discussion covering only the expressly excluded corrective work.
D. A declaration that no issues can be identified until every unrelated measure is approved.
Correct Answer: A
Full Explanation:
The assignment concerns issue identification for “Specialty coatings, textured finishes, and
decorative application procedures”. It expressly excludes the specified corrective work for
“Materials and Science”. The deliverable should reflect that boundary rather than implying that
identification also completes excluded analysis or approvals.
Question 5
Which technical focus most directly encompasses “Roller selection (nap sizes, core types)”?
A. Power tool operation, safety, and troubleshooting
B. Safety and Regulations
C. Tools and Equipment
D. Application Methods and Techniques
Correct Answer: D
Full Explanation:
Roller selection (nap sizes, core types) is an aspect of Application Methods and Techniques. This
choice preserves the specific relationship between the responsibility and its technical focus. The
other choices identify separate focuses, rather than the direct category of the activity described.
Question 6
Which focus best brings together these responsibilities: “Wood staining” and “Wallcovering
installation, layout, pattern matching, trimming, and adhesive selection”?
A. Tools and Equipment
B. Safety and Regulations
C. Application Methods and Techniques
D. Power tool operation, safety, and troubleshooting
Correct Answer: C
Full Explanation:
Both responsibilities are part of Application Methods and Techniques: Wood staining, and
Wallcovering installation, layout, pattern matching, trimming, and adhesive selection. Their
common technical focus is the reason this choice fits the pair. A different focus would not preserve
this specific grouping of responsibilities.
5521 Page 3
, PDCA Craftsperson Certification Examination Exam
Question 7
Which focus best brings together these responsibilities: “project documents” and “upon
completion”?
A. Safety and Regulations
B. Quality Control, Planning, and Job Standards
C. Tools and Equipment
D. Power tool operation, safety, and troubleshooting
Correct Answer: B
Full Explanation:
Both responsibilities are part of Quality Control, Planning, and Job Standards: project documents,
and upon completion. Their common technical focus is the reason this choice fits the pair. A
different focus would not preserve this specific grouping of responsibilities.
Question 8
A practice rule requires a follow-up discussion of “Brush application techniques, loading, cutting-in,
and film build control” whenever the review of “Clear finishes, stains, varnishes, lacquers, and wood
treatment products” raises an unresolved question. The first review raises such a question. Which
action follows from that rule?
A. Replace the unresolved question with an unrelated completed item to remove the trigger.
B. Omit the follow-up because unresolved questions always cancel discussion requirements.
C. Arrange the specified follow-up discussion because its stated trigger has occurred.
D. Record the follow-up as completed immediately when the trigger occurs.
Correct Answer: C
Full Explanation:
The trigger is an unresolved question arising in the review of “Clear finishes, stains, varnishes,
lacquers, and wood treatment products”. Because the case states that this trigger occurred, the
required discussion of “Brush application techniques, loading, cutting-in, and film build control”
must be arranged. A requirement to perform follow-up is not evidence that follow-up has already
happened.
5521 Page 4
Certification
Examination Exam
,PDCA Craftsperson Certification Examination Exam
Question 1
Which focus best brings together these responsibilities: “Quality control inspection criteria during
execution and upon completion” and “jobsite cleanup”?
A. Power tool operation, safety, and troubleshooting
B. Quality Control, Planning, and Job Standards
C. Safety and Regulations
D. Tools and Equipment
Correct Answer: B
Full Explanation:
Both responsibilities are part of Quality Control, Planning, and Job Standards: Quality control
inspection criteria during execution and upon completion, and jobsite cleanup. Their common
technical focus is the reason this choice fits the pair. A different focus would not preserve this
specific grouping of responsibilities.
Question 2
Which technical focus most directly encompasses “dew point”?
A. Safety and Regulations
B. Power tool operation, safety, and troubleshooting
C. Tools and Equipment
D. Environmental limitations
Correct Answer: D
Full Explanation:
dew point is an aspect of Environmental limitations. This choice preserves the specific relationship
between the responsibility and its technical focus. The other choices identify separate focuses,
rather than the direct category of the activity described.
Question 3
A team roster assigns one person to “Airless and conventional paint spray equipment setup,
operation, cleaning, and safety” and another to “Equipment calibration, maintenance schedules, and
storage practices”. No completed work or review results are recorded. Which statement stays within
the roster’s evidentiary value?
A. Assigning two people proves that their work has been independently verified.
B. Both responsibilities are complete because named owners appear beside them.
C. Neither person is responsible until a passing result has already been obtained.
D. Responsibility has been assigned; execution and results are not established by the roster.
Correct Answer: D
Full Explanation:
The roster establishes ownership of the responsibilities for “Airless and conventional paint spray
equipment setup, operation, cleaning, and safety” and “Equipment calibration, maintenance
schedules, and storage practices”. Assignment, completion, and verification are separate states. A
named owner is not evidence that the assigned work has been carried out or that its result has
been accepted.
5521 Page 2
,PDCA Craftsperson Certification Examination Exam
Question 4
A discussion is limited to identifying issues concerning “Specialty coatings, textured finishes, and
decorative application procedures”; selecting corrective measures for “Materials and Science” is
expressly outside its assignment. Which deliverable best respects that boundary?
A. An issue-identification discussion within the assigned subject, without claiming the excluded
corrective work.
B. A claim that corrective measures are approved merely because issues were identified.
C. A replacement discussion covering only the expressly excluded corrective work.
D. A declaration that no issues can be identified until every unrelated measure is approved.
Correct Answer: A
Full Explanation:
The assignment concerns issue identification for “Specialty coatings, textured finishes, and
decorative application procedures”. It expressly excludes the specified corrective work for
“Materials and Science”. The deliverable should reflect that boundary rather than implying that
identification also completes excluded analysis or approvals.
Question 5
Which technical focus most directly encompasses “Roller selection (nap sizes, core types)”?
A. Power tool operation, safety, and troubleshooting
B. Safety and Regulations
C. Tools and Equipment
D. Application Methods and Techniques
Correct Answer: D
Full Explanation:
Roller selection (nap sizes, core types) is an aspect of Application Methods and Techniques. This
choice preserves the specific relationship between the responsibility and its technical focus. The
other choices identify separate focuses, rather than the direct category of the activity described.
Question 6
Which focus best brings together these responsibilities: “Wood staining” and “Wallcovering
installation, layout, pattern matching, trimming, and adhesive selection”?
A. Tools and Equipment
B. Safety and Regulations
C. Application Methods and Techniques
D. Power tool operation, safety, and troubleshooting
Correct Answer: C
Full Explanation:
Both responsibilities are part of Application Methods and Techniques: Wood staining, and
Wallcovering installation, layout, pattern matching, trimming, and adhesive selection. Their
common technical focus is the reason this choice fits the pair. A different focus would not preserve
this specific grouping of responsibilities.
5521 Page 3
, PDCA Craftsperson Certification Examination Exam
Question 7
Which focus best brings together these responsibilities: “project documents” and “upon
completion”?
A. Safety and Regulations
B. Quality Control, Planning, and Job Standards
C. Tools and Equipment
D. Power tool operation, safety, and troubleshooting
Correct Answer: B
Full Explanation:
Both responsibilities are part of Quality Control, Planning, and Job Standards: project documents,
and upon completion. Their common technical focus is the reason this choice fits the pair. A
different focus would not preserve this specific grouping of responsibilities.
Question 8
A practice rule requires a follow-up discussion of “Brush application techniques, loading, cutting-in,
and film build control” whenever the review of “Clear finishes, stains, varnishes, lacquers, and wood
treatment products” raises an unresolved question. The first review raises such a question. Which
action follows from that rule?
A. Replace the unresolved question with an unrelated completed item to remove the trigger.
B. Omit the follow-up because unresolved questions always cancel discussion requirements.
C. Arrange the specified follow-up discussion because its stated trigger has occurred.
D. Record the follow-up as completed immediately when the trigger occurs.
Correct Answer: C
Full Explanation:
The trigger is an unresolved question arising in the review of “Clear finishes, stains, varnishes,
lacquers, and wood treatment products”. Because the case states that this trigger occurred, the
required discussion of “Brush application techniques, loading, cutting-in, and film build control”
must be arranged. A requirement to perform follow-up is not evidence that follow-up has already
happened.
5521 Page 4
