National Association of Corrosion Engineers. Coating Inspector
Program. - Computer-Based Testing.NACE CIP 1 CBT Actual Exam 2026
|| Most Recent Exam 2026|2027 Actual Complete Real Exam
Questions And Correct Answers (Verified Answers) Already Graded A+
| Guaranteed Success!! Newest Exam | Just Released!!
The least effective method of surface cleaning is most likely: -ANSWER-
Hand Tool Cleaning
Nace No. 4/SSPC SP 7 is a joint standard for: -ANSWER-Brush Off Blast
Cleaning
Surface profiles describes: -ANSWER-The level of surface roughness
required after abrasive blasting.
To be of value the Inspectors documentation must be: -ANSWER-
Timely, accurate and concise.
A NACE Coating Inspector is permitted to transport coating material
when: -ANSWER-The Inspector should never transport coating material.
Solvents are added to coating formulations to: -ANSWER-Dissolve
binders and form liquid coatings.
,(Also known as 'fisheyes' or 'crawling') is the term for surface breaks in
the film that reveal the substrate. It is often a result of grease or oil
contamination on the substrate. -ANSWER-Cissing
Which coating cures the fastest? -ANSWER-Polyurea
Amine blush is likely to occur with which type of coating? -ANSWER-
Epoxy
You are the Inspector on a project where specification level of
cleaniness is "near white". Which standard would you follow? -
ANSWER-NACE No. 2/SSPC SP 10
The powerful standard for cleaning to bare metal with a minimum
profile of 1 Mill (25.4microns) is: -ANSWER-SSPC SP 11
Which profile comparators are referenced by ISO 8503? -ANSWER-Grit
and Shot
On blast cleaned surfaces, an ultraviolet light can reveal? -ANSWER-Oil
The Inspector on a project with a sprayed polyurethane coating. The
most probable safety concern is? -ANSWER-Isocyanates
, When applied to concrete, alkyd coatings will fall prematurely due to? -
ANSWER-Saponification
Water borne latex coatings cure by a process known as? -ANSWER-
Coalescence
Coatings that cure by polymerization are? -ANSWER-Convertible
A pre job conference should be held: -ANSWER-after bids have been
submitted and contracts signed.
Which standard gives guidelines for how many DFT measurements
should be taken in a given area? -ANSWER-SSPC PA 2
You are on a job and observe the coating being applied in an
unacceptable manner. As the Inspector you should? -ANSWER-Report
to the Contractor's Supervisor and Report to the Owner's
Representative.
When applying coatings, generally high relative humidity it: -ANSWER-
slows solvent evaporation
Generally speaking, on a typical coating project overall safety is the
responsibility of? -ANSWER-A certified safety professional. Commented [U1]:
Program. - Computer-Based Testing.NACE CIP 1 CBT Actual Exam 2026
|| Most Recent Exam 2026|2027 Actual Complete Real Exam
Questions And Correct Answers (Verified Answers) Already Graded A+
| Guaranteed Success!! Newest Exam | Just Released!!
The least effective method of surface cleaning is most likely: -ANSWER-
Hand Tool Cleaning
Nace No. 4/SSPC SP 7 is a joint standard for: -ANSWER-Brush Off Blast
Cleaning
Surface profiles describes: -ANSWER-The level of surface roughness
required after abrasive blasting.
To be of value the Inspectors documentation must be: -ANSWER-
Timely, accurate and concise.
A NACE Coating Inspector is permitted to transport coating material
when: -ANSWER-The Inspector should never transport coating material.
Solvents are added to coating formulations to: -ANSWER-Dissolve
binders and form liquid coatings.
,(Also known as 'fisheyes' or 'crawling') is the term for surface breaks in
the film that reveal the substrate. It is often a result of grease or oil
contamination on the substrate. -ANSWER-Cissing
Which coating cures the fastest? -ANSWER-Polyurea
Amine blush is likely to occur with which type of coating? -ANSWER-
Epoxy
You are the Inspector on a project where specification level of
cleaniness is "near white". Which standard would you follow? -
ANSWER-NACE No. 2/SSPC SP 10
The powerful standard for cleaning to bare metal with a minimum
profile of 1 Mill (25.4microns) is: -ANSWER-SSPC SP 11
Which profile comparators are referenced by ISO 8503? -ANSWER-Grit
and Shot
On blast cleaned surfaces, an ultraviolet light can reveal? -ANSWER-Oil
The Inspector on a project with a sprayed polyurethane coating. The
most probable safety concern is? -ANSWER-Isocyanates
, When applied to concrete, alkyd coatings will fall prematurely due to? -
ANSWER-Saponification
Water borne latex coatings cure by a process known as? -ANSWER-
Coalescence
Coatings that cure by polymerization are? -ANSWER-Convertible
A pre job conference should be held: -ANSWER-after bids have been
submitted and contracts signed.
Which standard gives guidelines for how many DFT measurements
should be taken in a given area? -ANSWER-SSPC PA 2
You are on a job and observe the coating being applied in an
unacceptable manner. As the Inspector you should? -ANSWER-Report
to the Contractor's Supervisor and Report to the Owner's
Representative.
When applying coatings, generally high relative humidity it: -ANSWER-
slows solvent evaporation
Generally speaking, on a typical coating project overall safety is the
responsibility of? -ANSWER-A certified safety professional. Commented [U1]:
