Michigan Builders Residential Builder Actual Exam 2026 || Most
Recent Exam 2026|2027 Actual Complete Real Exam Questions And
Correct Answers (Verified Answers) Already Graded A+ | Guaranteed
Success!! Newest Exam | Just Released!!
For what reason would you use a story pole? -ANSWER-to layout
windows and doors
Holes bored in a single stud in exterior walls and bearing walls shall not
exceed 40% of the stud depth and not be closer than
__________________ to the edge of the stud. -ANSWER-5/8"
Floor framing consists of: -ANSWER-joist, posts, girders and sills
When making a wood girder using 2" lumber, you should use ______
nails for each layer and nails should be spaced ________ at tops and
bottoms and staggered, with 2 nails at each end and at each splice. -
ANSWER-10d nails, 32" o.c.
Roof assemblies subject to wind uplift pressures of ______ per square
foot or greater require approved connectors between the top plate and
rafter or truss. -ANSWER-20 lbs.
Walls can be braced with the materials that cover them as long as the
material provides the structural strength. T F -ANSWER-True
,Where practical, an I-beam can be replaced in residential construction
by: -ANSWER-a load bearing wall
The bottom horizontal member of a wall frame in platform construction
is called a: -ANSWER-soleplate
The horizontal member located at the top of a wall frame is called: -
ANSWER-top plate
The best type of nail to attach a 4 x 8 sheet of exterior plywood used as
siding or soffit, above grade is: -ANSWER-noncorrosive
A saddle is used: -ANSWER-between the roof and chimney
A cricket is used: -ANSWER-between the roof and a chimney
Bracing which prevents joists from moving side to side is called: -
ANSWER-bridging
Diagonal bracing (corner or wind) is normally installed at a ______
degree angle. -ANSWER-45
Rafters and floor joists should be installed with the: -ANSWER-crown up
,Deflection could be defined as: -ANSWER-sag
A carpenter should never release the truss being installed from the
lifting sling until_________. -ANSWER-all TCTLB are installed and
bearing attachments are made
When preparing to set roof trusses, substantial ___________ of the
first truss is critical for the proper installation and safety concerns of
the project. -ANSWER-ground bracing
The diagonal member in a wall frame is a: -ANSWER-corner brace
The mark C-D stamped on a sheet of plywood refers to the: -ANSWER-
veneer grade
The type of wall framing most often built on a horizontal surface and
then tilted up is called: -ANSWER-platform framing
The required fastening for securing a sole plate to a joist or blocking at
braced wall panels is: -ANSWER-3-16d nails, 16" o.c.
What would be an advantage of platform frame construction over
balloon frame construction? -ANSWER-Easily adapted to prefabrication
, It does not require unusually long lengths of lumber
On multi-story buildings, firestops are built into the construction
The first step in wall framing is to: -ANSWER-lay out wall locations on
the subfloor
When laying out the soleplate, lay out door and window openings,
partitions and _______________. -ANSWER-stud locations
A sheet of plywood stamped 32/16 has a maximum span of: -ANSWER-
32" roof sheathing and 16" subflooring
The minimum hall width in a single family dwelling is: -ANSWER-36"
Recommended installation of sheet subflooring over joists is: -ANSWER-
perpendicular to joists
When should bridging be installed? -ANSWER-the top of the bridging is
nailed before, and the bottom is nailed after the subfloor is nailed
The material placed between the sill plate and the top of the
foundation wall is called: -ANSWER-sill sealer
Recent Exam 2026|2027 Actual Complete Real Exam Questions And
Correct Answers (Verified Answers) Already Graded A+ | Guaranteed
Success!! Newest Exam | Just Released!!
For what reason would you use a story pole? -ANSWER-to layout
windows and doors
Holes bored in a single stud in exterior walls and bearing walls shall not
exceed 40% of the stud depth and not be closer than
__________________ to the edge of the stud. -ANSWER-5/8"
Floor framing consists of: -ANSWER-joist, posts, girders and sills
When making a wood girder using 2" lumber, you should use ______
nails for each layer and nails should be spaced ________ at tops and
bottoms and staggered, with 2 nails at each end and at each splice. -
ANSWER-10d nails, 32" o.c.
Roof assemblies subject to wind uplift pressures of ______ per square
foot or greater require approved connectors between the top plate and
rafter or truss. -ANSWER-20 lbs.
Walls can be braced with the materials that cover them as long as the
material provides the structural strength. T F -ANSWER-True
,Where practical, an I-beam can be replaced in residential construction
by: -ANSWER-a load bearing wall
The bottom horizontal member of a wall frame in platform construction
is called a: -ANSWER-soleplate
The horizontal member located at the top of a wall frame is called: -
ANSWER-top plate
The best type of nail to attach a 4 x 8 sheet of exterior plywood used as
siding or soffit, above grade is: -ANSWER-noncorrosive
A saddle is used: -ANSWER-between the roof and chimney
A cricket is used: -ANSWER-between the roof and a chimney
Bracing which prevents joists from moving side to side is called: -
ANSWER-bridging
Diagonal bracing (corner or wind) is normally installed at a ______
degree angle. -ANSWER-45
Rafters and floor joists should be installed with the: -ANSWER-crown up
,Deflection could be defined as: -ANSWER-sag
A carpenter should never release the truss being installed from the
lifting sling until_________. -ANSWER-all TCTLB are installed and
bearing attachments are made
When preparing to set roof trusses, substantial ___________ of the
first truss is critical for the proper installation and safety concerns of
the project. -ANSWER-ground bracing
The diagonal member in a wall frame is a: -ANSWER-corner brace
The mark C-D stamped on a sheet of plywood refers to the: -ANSWER-
veneer grade
The type of wall framing most often built on a horizontal surface and
then tilted up is called: -ANSWER-platform framing
The required fastening for securing a sole plate to a joist or blocking at
braced wall panels is: -ANSWER-3-16d nails, 16" o.c.
What would be an advantage of platform frame construction over
balloon frame construction? -ANSWER-Easily adapted to prefabrication
, It does not require unusually long lengths of lumber
On multi-story buildings, firestops are built into the construction
The first step in wall framing is to: -ANSWER-lay out wall locations on
the subfloor
When laying out the soleplate, lay out door and window openings,
partitions and _______________. -ANSWER-stud locations
A sheet of plywood stamped 32/16 has a maximum span of: -ANSWER-
32" roof sheathing and 16" subflooring
The minimum hall width in a single family dwelling is: -ANSWER-36"
Recommended installation of sheet subflooring over joists is: -ANSWER-
perpendicular to joists
When should bridging be installed? -ANSWER-the top of the bridging is
nailed before, and the bottom is nailed after the subfloor is nailed
The material placed between the sill plate and the top of the
foundation wall is called: -ANSWER-sill sealer
