Michigan Fire Alarm Specialty
Technician Exam Questions and Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
Question 1
What is the minimum passing score specified for the Michigan Fire Alarm
Specialty Technician examination?
A. 65%
B. 70%
C. 75%
D. 80%
Correct Answer: C
Rationale: The current Michigan PSI Candidate Information Bulletin specifies a
minimum passing score of 75% for the Fire Alarm Specialty Technician
examination.
Question 2
According to the current Michigan examination bulletin, which NEC edition forms
the basis for Fire Alarm Specialty Technician examination questions?
A. 2017 NEC
B. 2020 NEC
C. 2023 NEC
D. 2026 NEC
Correct Answer: C
,Rationale: The current bulletin states that other NEC editions may be used during
the examination, but the examination items are based on the 2023 edition.
Question 3
Which NEC article is specifically associated with fire alarm systems and circuits?
A. Article 430
B. Article 760
C. Article 680
D. Article 820
Correct Answer: B
Rationale: NEC Article 760 addresses fire alarm systems, including fire alarm
circuits, power supplies, wiring methods, and related installation requirements.
Question 4
What is the primary purpose of a fire alarm initiating device?
A. Provide electrical grounding
B. Supply standby power
C. Detect a condition that can initiate a fire alarm signal
D. Protect a circuit from overcurrent
Correct Answer: C
Rationale: Initiating devices detect conditions such as smoke, heat, or manual
activation and provide a signal to the fire alarm system.
Question 5
Which device is normally considered an initiating device?
A. Smoke detector
B. Notification appliance
C. Control relay
D. Power supply
Correct Answer: A
,Rationale: A smoke detector senses smoke and provides an initiating signal to the
fire alarm system.
Question 6
What is the primary function of a fire alarm notification appliance?
A. Detect smoke
B. Notify occupants or other required parties of an alarm condition
C. Provide overcurrent protection
D. Monitor conductor insulation
Correct Answer: B
Rationale: Notification appliances provide audible, visible, or other required
signals to communicate alarm or emergency conditions.
Question 7
What is the primary purpose of a fire alarm control unit?
A. Control and coordinate signals received from system devices
B. Replace all initiating devices
C. Provide building structural support
D. Serve as a general-purpose lighting panel
Correct Answer: A
Rationale: The fire alarm control unit receives signals from initiating devices and
controls system functions such as notification and supervisory or trouble signaling.
Question 8
Which condition is most likely to produce a trouble signal rather than a fire alarm
signal?
A. Manual pull station activation
B. Smoke detector operation
C. Open circuit in a supervised circuit
D. Automatic sprinkler waterflow activation
Correct Answer: C
, Rationale: A break or other fault in a supervised circuit can cause the control unit
to indicate a trouble condition because the circuit is no longer being properly
monitored.
Question 9
What is the main purpose of circuit supervision in a fire alarm system?
A. Increase conductor resistance
B. Detect certain faults that could impair circuit operation
C. Increase notification appliance volume
D. Eliminate the need for testing
Correct Answer: B
Rationale: Supervision allows the system to monitor wiring and connected
equipment for specified faults, helping identify conditions that could impair system
operation.
Question 10
Which conductor characteristic directly affects voltage drop in a fire alarm circuit?
A. Conductor resistance
B. Conduit color
C. Box shape
D. Device mounting height
Correct Answer: A
Rationale: Conductor resistance contributes directly to voltage drop. Longer runs,
smaller conductors, and higher current generally increase voltage drop.
Question 11
A fire alarm notification circuit has excessive voltage drop. What is a likely result?
A. Notification appliances may not operate properly
B. Grounding becomes unnecessary
C. The circuit automatically becomes Class 2
D. The control unit becomes mechanically damaged
Correct Answer: A
Technician Exam Questions and Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
Question 1
What is the minimum passing score specified for the Michigan Fire Alarm
Specialty Technician examination?
A. 65%
B. 70%
C. 75%
D. 80%
Correct Answer: C
Rationale: The current Michigan PSI Candidate Information Bulletin specifies a
minimum passing score of 75% for the Fire Alarm Specialty Technician
examination.
Question 2
According to the current Michigan examination bulletin, which NEC edition forms
the basis for Fire Alarm Specialty Technician examination questions?
A. 2017 NEC
B. 2020 NEC
C. 2023 NEC
D. 2026 NEC
Correct Answer: C
,Rationale: The current bulletin states that other NEC editions may be used during
the examination, but the examination items are based on the 2023 edition.
Question 3
Which NEC article is specifically associated with fire alarm systems and circuits?
A. Article 430
B. Article 760
C. Article 680
D. Article 820
Correct Answer: B
Rationale: NEC Article 760 addresses fire alarm systems, including fire alarm
circuits, power supplies, wiring methods, and related installation requirements.
Question 4
What is the primary purpose of a fire alarm initiating device?
A. Provide electrical grounding
B. Supply standby power
C. Detect a condition that can initiate a fire alarm signal
D. Protect a circuit from overcurrent
Correct Answer: C
Rationale: Initiating devices detect conditions such as smoke, heat, or manual
activation and provide a signal to the fire alarm system.
Question 5
Which device is normally considered an initiating device?
A. Smoke detector
B. Notification appliance
C. Control relay
D. Power supply
Correct Answer: A
,Rationale: A smoke detector senses smoke and provides an initiating signal to the
fire alarm system.
Question 6
What is the primary function of a fire alarm notification appliance?
A. Detect smoke
B. Notify occupants or other required parties of an alarm condition
C. Provide overcurrent protection
D. Monitor conductor insulation
Correct Answer: B
Rationale: Notification appliances provide audible, visible, or other required
signals to communicate alarm or emergency conditions.
Question 7
What is the primary purpose of a fire alarm control unit?
A. Control and coordinate signals received from system devices
B. Replace all initiating devices
C. Provide building structural support
D. Serve as a general-purpose lighting panel
Correct Answer: A
Rationale: The fire alarm control unit receives signals from initiating devices and
controls system functions such as notification and supervisory or trouble signaling.
Question 8
Which condition is most likely to produce a trouble signal rather than a fire alarm
signal?
A. Manual pull station activation
B. Smoke detector operation
C. Open circuit in a supervised circuit
D. Automatic sprinkler waterflow activation
Correct Answer: C
, Rationale: A break or other fault in a supervised circuit can cause the control unit
to indicate a trouble condition because the circuit is no longer being properly
monitored.
Question 9
What is the main purpose of circuit supervision in a fire alarm system?
A. Increase conductor resistance
B. Detect certain faults that could impair circuit operation
C. Increase notification appliance volume
D. Eliminate the need for testing
Correct Answer: B
Rationale: Supervision allows the system to monitor wiring and connected
equipment for specified faults, helping identify conditions that could impair system
operation.
Question 10
Which conductor characteristic directly affects voltage drop in a fire alarm circuit?
A. Conductor resistance
B. Conduit color
C. Box shape
D. Device mounting height
Correct Answer: A
Rationale: Conductor resistance contributes directly to voltage drop. Longer runs,
smaller conductors, and higher current generally increase voltage drop.
Question 11
A fire alarm notification circuit has excessive voltage drop. What is a likely result?
A. Notification appliances may not operate properly
B. Grounding becomes unnecessary
C. The circuit automatically becomes Class 2
D. The control unit becomes mechanically damaged
Correct Answer: A
