PIPEFITTER STAR EXAM PREPARATION
TEST BANK WITH CORRECT ANSWERS
●● Fall hazards, Electrical hazards, Caught in, Struck by
Answer: Four focus inspectioin OSHA compliance officers look for:
●● Plane End Square Cut (PESC)
Thread and Coupling (T&C)
Thread Both Ends (TBE)
Answer: Steel pipe is supplied with the following end finish:
●● Start/Stop, Regulate/Throttle, Relief, Reduce
Answer: Four principle functions of valves
●● 125F
Answer: Never expose any part of a compressed gas cylinder to
temperatures above:
●● 350F
Answer: Max service temperature of a brazed joint?
●● Straight, Choker, Basket
,Answer: Three basic hitches which can be used for lifting with a sling
●● 6300F
Answer: Oxyacetylene flame has a peak temperature of roughly:
●● Immediate danger to Live and Health
Answer: IDLH in regards to OSHA stands for
●● Inhalation, ingestion, absorption, and injection.
Answer: Four routes of entry into the human body are
●● Are impelled along a conductor
Answer: When voltage is applied along a conductor, free electrons:
●● Exists at all points along it's length
Answer: The magnetic field around a current carrying wire:
●● Voltage/Amps
Answer: What is the formula for electrical resistance (ohms)
●● Thermocouple
Answer: A ________ generates a small amount of voltage when heated.
, ●● Sensible heat
Answer: The quantity of heat involved to change a substance that can be
measured with a thermometer.
●● Latent heat
Answer: The amount of heat required to bring about a change in state in
a substance.
●● Specific heat
Answer: The amount of heat in BTU's required to change the
temperature of 1 lb of a substance 1 degree F
●● force per unit of area
Answer: Pressure is ___________ per _________ _______
●● Positive diplacement and Non-positive displacement pumps.
Answer: Name the two main classifications of pump types
●● Parallel and Angular alignment
Answer: What are two kinds of misalignment that must be checked for
when installing pumps?
TEST BANK WITH CORRECT ANSWERS
●● Fall hazards, Electrical hazards, Caught in, Struck by
Answer: Four focus inspectioin OSHA compliance officers look for:
●● Plane End Square Cut (PESC)
Thread and Coupling (T&C)
Thread Both Ends (TBE)
Answer: Steel pipe is supplied with the following end finish:
●● Start/Stop, Regulate/Throttle, Relief, Reduce
Answer: Four principle functions of valves
●● 125F
Answer: Never expose any part of a compressed gas cylinder to
temperatures above:
●● 350F
Answer: Max service temperature of a brazed joint?
●● Straight, Choker, Basket
,Answer: Three basic hitches which can be used for lifting with a sling
●● 6300F
Answer: Oxyacetylene flame has a peak temperature of roughly:
●● Immediate danger to Live and Health
Answer: IDLH in regards to OSHA stands for
●● Inhalation, ingestion, absorption, and injection.
Answer: Four routes of entry into the human body are
●● Are impelled along a conductor
Answer: When voltage is applied along a conductor, free electrons:
●● Exists at all points along it's length
Answer: The magnetic field around a current carrying wire:
●● Voltage/Amps
Answer: What is the formula for electrical resistance (ohms)
●● Thermocouple
Answer: A ________ generates a small amount of voltage when heated.
, ●● Sensible heat
Answer: The quantity of heat involved to change a substance that can be
measured with a thermometer.
●● Latent heat
Answer: The amount of heat required to bring about a change in state in
a substance.
●● Specific heat
Answer: The amount of heat in BTU's required to change the
temperature of 1 lb of a substance 1 degree F
●● force per unit of area
Answer: Pressure is ___________ per _________ _______
●● Positive diplacement and Non-positive displacement pumps.
Answer: Name the two main classifications of pump types
●● Parallel and Angular alignment
Answer: What are two kinds of misalignment that must be checked for
when installing pumps?
