CO Drywall Contractor Exam Questions and
Correct Answers (Verified Answers) Plus
Rationale 2027 Q&A| Instant Download
Pdf
1. Which drywall panel is most commonly used for interior wall and
ceiling applications in dry areas?
A. Type X gypsum panel
B. Cement backer board
C. Standard gypsum wallboard
D. Exterior sheathing panel
Answer: C. Standard gypsum wallboard
Rationale: Standard gypsum wallboard is designed for typical interior
applications where there is no unusual exposure to moisture, fire, or
impact. Type X is selected when a fire-resistance rating is required,
while cement board is generally used in wet-area or tile applications.
, 2. What is the primary purpose of the paper facing on a gypsum
drywall panel?
A. To increase electrical conductivity
B. To provide a finished surface and reinforce the gypsum core
C. To make the panel waterproof
D. To eliminate the need for joint compound
Answer: B. To provide a finished surface and reinforce the gypsum
core
Rationale: The paper facing helps reinforce the gypsum core and
provides a suitable surface for finishing with joint compound, primer,
and paint. Standard paper-faced drywall should not be considered
waterproof merely because it has a paper facing.
3. Which drywall type is specifically manufactured to provide
improved fire resistance?
A. Type X gypsum board
B. Sound-deadening board only
C. Standard 1/4-inch board
D. Moisture-resistant board
Answer: A. Type X gypsum board
,Rationale: Type X gypsum board contains additives and is
manufactured to provide greater fire resistance than ordinary gypsum
board. Its use is common in assemblies requiring a tested fire-
resistance rating.
4. What is the primary purpose of drywall joint compound?
A. To strengthen wood framing
B. To fill joints, fastener heads, and surface imperfections
C. To waterproof the entire wall
D. To replace drywall fasteners
Answer: B. To fill joints, fastener heads, and surface imperfections
Rationale: Joint compound is used with joint tape to create smooth,
continuous drywall surfaces. It is also used to cover screw or nail
heads and minor surface defects before sanding and finishing.
5. Why is joint tape installed over drywall joints?
A. To increase insulation value
B. To prevent electrical shorts
C. To reinforce the joint and reduce cracking
D. To replace corner bead
Answer: C. To reinforce the joint and reduce cracking
, Rationale: Drywall joints create a potential weak point between
panels. Joint tape reinforces the seam and, when properly embedded
in joint compound, helps produce a durable finished joint that is less
likely to crack.
6. Which tool is commonly used to cut gypsum drywall panels?
A. Drywall utility knife
B. Pipe wrench
C. Cold chisel only
D. Pipe cutter
Answer: A. Drywall utility knife
Rationale: A sharp utility knife is commonly used to score the face
paper and gypsum core. The panel can then be snapped along the
scored line and the back paper cut to complete the separation.
7. What is the purpose of a drywall T-square?
A. Measuring electrical voltage
B. Producing straight layout and cutting lines
C. Applying joint compound
D. Driving drywall screws
Answer: B. Producing straight layout and cutting lines
Correct Answers (Verified Answers) Plus
Rationale 2027 Q&A| Instant Download
1. Which drywall panel is most commonly used for interior wall and
ceiling applications in dry areas?
A. Type X gypsum panel
B. Cement backer board
C. Standard gypsum wallboard
D. Exterior sheathing panel
Answer: C. Standard gypsum wallboard
Rationale: Standard gypsum wallboard is designed for typical interior
applications where there is no unusual exposure to moisture, fire, or
impact. Type X is selected when a fire-resistance rating is required,
while cement board is generally used in wet-area or tile applications.
, 2. What is the primary purpose of the paper facing on a gypsum
drywall panel?
A. To increase electrical conductivity
B. To provide a finished surface and reinforce the gypsum core
C. To make the panel waterproof
D. To eliminate the need for joint compound
Answer: B. To provide a finished surface and reinforce the gypsum
core
Rationale: The paper facing helps reinforce the gypsum core and
provides a suitable surface for finishing with joint compound, primer,
and paint. Standard paper-faced drywall should not be considered
waterproof merely because it has a paper facing.
3. Which drywall type is specifically manufactured to provide
improved fire resistance?
A. Type X gypsum board
B. Sound-deadening board only
C. Standard 1/4-inch board
D. Moisture-resistant board
Answer: A. Type X gypsum board
,Rationale: Type X gypsum board contains additives and is
manufactured to provide greater fire resistance than ordinary gypsum
board. Its use is common in assemblies requiring a tested fire-
resistance rating.
4. What is the primary purpose of drywall joint compound?
A. To strengthen wood framing
B. To fill joints, fastener heads, and surface imperfections
C. To waterproof the entire wall
D. To replace drywall fasteners
Answer: B. To fill joints, fastener heads, and surface imperfections
Rationale: Joint compound is used with joint tape to create smooth,
continuous drywall surfaces. It is also used to cover screw or nail
heads and minor surface defects before sanding and finishing.
5. Why is joint tape installed over drywall joints?
A. To increase insulation value
B. To prevent electrical shorts
C. To reinforce the joint and reduce cracking
D. To replace corner bead
Answer: C. To reinforce the joint and reduce cracking
, Rationale: Drywall joints create a potential weak point between
panels. Joint tape reinforces the seam and, when properly embedded
in joint compound, helps produce a durable finished joint that is less
likely to crack.
6. Which tool is commonly used to cut gypsum drywall panels?
A. Drywall utility knife
B. Pipe wrench
C. Cold chisel only
D. Pipe cutter
Answer: A. Drywall utility knife
Rationale: A sharp utility knife is commonly used to score the face
paper and gypsum core. The panel can then be snapped along the
scored line and the back paper cut to complete the separation.
7. What is the purpose of a drywall T-square?
A. Measuring electrical voltage
B. Producing straight layout and cutting lines
C. Applying joint compound
D. Driving drywall screws
Answer: B. Producing straight layout and cutting lines
