FLORIDA HOME INSPECTOR 1
EXAM 2027 WITH 300 QUESTIONS
AND EXPERT-VERIFIED
CORRECT ANSWERS | AREADY
GRADED A+ | GUARANTEED PASS
The inspector should___ when reporting on an asbestos cement tile roof. -
ANSWER-Not the roof material
The size of a standard roll roofing is ____ inches wide. - ANSWER-36
The layers that make up a built-up roof are called. - ANSWER-Plys
T/F: alligatoring of a roof covering is only a cosmetic issue. - ANSWER-False
When a flat roof has water stains, these are signs of previous. - ANSWER-Ponding
,Metal roof tiles are typically made of___. - ANSWER-Steel
Crushed Stone or gravel ballast on a built-up rood___. - ANSWER-Protects the
roof from sunlight
_____ is normally used for flashing. - ANSWER-Timber
_____ flashing is the type of flashing that goes between the roof covering and the
sheathing around the roof's perimeter. - ANSWER-Drip Edge
A flashing along the peak of the roof is called the - ANSWER-Ridge
A closed valley means that the valley flashing___. - ANSWER-Cannot be seen
Metal valley flashing should be a minimum of ___ inches wide. - ANSWER-24
For most tile roofs, a standard step flashing cannot be used against a wall, so a
_____ flashing must be installed. - ANSWER-Pan
The bottom of . roof should have a ____ flashing where it meets a wall. -
ANSWER-Kickout
T:F/ A common location for an apron flashing is at the front side or downslope
side of a chimney. - ANSWER-Ture
, An attic with an area of 600 square feet with ridge and soffit vents should have a
total vent area of ___ square feet. - ANSWER-2
The____ effective venting system for most type of roofs is ridge and soffit vents. -
ANSWER-Most
An attic space with only gable vents should have a vent area of 1 square foot
per___ square foot of floor area. - ANSWER-150
T/F: roof vents are required for roof vents with an unconditioned attic space. -
ANSWER-True
Flat roofs normally have____ venting systems. - ANSWER-Passive
Branch circuitconductorsarethe____________ - ANSWER-wires to the outlet
Voltage is equal to - ANSWER-amps X resistance
If a service entrance has a 200-amp supply, the minimum cable size should be? -
ANSWER-2/0 copper or 4/0 aluminum
The following item is safe to insert into an electrical panel: - ANSWER-Nothing
The main panel is also called the? - ANSWER-Electrical Panel
_____ are the units used to measure resistance. - ANSWER-Ohms
EXAM 2027 WITH 300 QUESTIONS
AND EXPERT-VERIFIED
CORRECT ANSWERS | AREADY
GRADED A+ | GUARANTEED PASS
The inspector should___ when reporting on an asbestos cement tile roof. -
ANSWER-Not the roof material
The size of a standard roll roofing is ____ inches wide. - ANSWER-36
The layers that make up a built-up roof are called. - ANSWER-Plys
T/F: alligatoring of a roof covering is only a cosmetic issue. - ANSWER-False
When a flat roof has water stains, these are signs of previous. - ANSWER-Ponding
,Metal roof tiles are typically made of___. - ANSWER-Steel
Crushed Stone or gravel ballast on a built-up rood___. - ANSWER-Protects the
roof from sunlight
_____ is normally used for flashing. - ANSWER-Timber
_____ flashing is the type of flashing that goes between the roof covering and the
sheathing around the roof's perimeter. - ANSWER-Drip Edge
A flashing along the peak of the roof is called the - ANSWER-Ridge
A closed valley means that the valley flashing___. - ANSWER-Cannot be seen
Metal valley flashing should be a minimum of ___ inches wide. - ANSWER-24
For most tile roofs, a standard step flashing cannot be used against a wall, so a
_____ flashing must be installed. - ANSWER-Pan
The bottom of . roof should have a ____ flashing where it meets a wall. -
ANSWER-Kickout
T:F/ A common location for an apron flashing is at the front side or downslope
side of a chimney. - ANSWER-Ture
, An attic with an area of 600 square feet with ridge and soffit vents should have a
total vent area of ___ square feet. - ANSWER-2
The____ effective venting system for most type of roofs is ridge and soffit vents. -
ANSWER-Most
An attic space with only gable vents should have a vent area of 1 square foot
per___ square foot of floor area. - ANSWER-150
T/F: roof vents are required for roof vents with an unconditioned attic space. -
ANSWER-True
Flat roofs normally have____ venting systems. - ANSWER-Passive
Branch circuitconductorsarethe____________ - ANSWER-wires to the outlet
Voltage is equal to - ANSWER-amps X resistance
If a service entrance has a 200-amp supply, the minimum cable size should be? -
ANSWER-2/0 copper or 4/0 aluminum
The following item is safe to insert into an electrical panel: - ANSWER-Nothing
The main panel is also called the? - ANSWER-Electrical Panel
_____ are the units used to measure resistance. - ANSWER-Ohms
