HYDRONICS 4 SOLVED CORRECTLY LATEST UPDATE 2027 GRADED
A+
Question 1.
A ___ has many of the same components as an end-suction flexibly coupled pump but does
not employ a pump shaft or pump bearing assembly.
Correct Answer: close-coupled end-suction pump
Question 2.
A ___ valve is a valve that permits fluid flow in only one direction and closes automatically
to prevent backflow.
Correct Answer: check
Question 3.
A high head pump is a pump classified as above ___ hp and operating above 12' of
pressure head.
Correct Answer: 1/2
Question 4.
A pump is installed with the compression tank connection on the suction side of the pump
in a closed loop system. The static pressure is 15 psig and the pump delivers 60 feet of
head when running. With the pump running, the discharge gage would read _____ psig, and
the suction gage would read _____ psig. (round the answers to the nearest whole number)
Correct Answer: 41, 15
Question 5.
A recommended grout mixture is one part cement to ___ part(s) clean, sharp sand, wet
enough to flow freely.
Correct Answer: two
Question 6.
A section of straight pipe should never be installed between the suction side of a pump
and first elbow.
Correct Answer: False
Question 7.
A suction diffuser acts as a high pressure drop device that can be installed at the pump
suction.
Correct Answer: False
, Question 8.
A wet rotor circulator uses system fluid for lubrication.
Correct Answer: True
Question 9.
A(n) ___ impeller is an impeller that has shrouds on both sides of the vanes.
Correct Answer: closed
Question 10.
A(n) ___ is the pump casing or body that contains the pumped HTF under pressure.
Correct Answer: volute
Question 11.
A(n) ____________________ is a device through which an external source of power is used to
apply a force to a fluid in order to move the fluid from one place to another.
Correct Answer: pump
Question 12.
A(n) ____________________ valve is a valve designed to regulate the rate of fluid flow
through a hydronic piping system to meet system requirements.
Correct Answer: balancing
Question 13.
All low-head pumps must pump away from the point of no pressure change.
Correct Answer: False
Question 14.
All-bronze pumps are used for recirculation lines in domestic hot water systems and for
pumping hot process water.
Correct Answer: True
Question 15.
Although ____________________ pumps have the advantage of being able to provide very
high pressures, they discharge fluids in a pulsating flow.
Correct Answer: reciprocating
Question 16.
As an impeller rotates, a low-pressure area is created at the eye of the impeller to allow
fluid to enter the suction side of the pump.
Correct Answer: True
A+
Question 1.
A ___ has many of the same components as an end-suction flexibly coupled pump but does
not employ a pump shaft or pump bearing assembly.
Correct Answer: close-coupled end-suction pump
Question 2.
A ___ valve is a valve that permits fluid flow in only one direction and closes automatically
to prevent backflow.
Correct Answer: check
Question 3.
A high head pump is a pump classified as above ___ hp and operating above 12' of
pressure head.
Correct Answer: 1/2
Question 4.
A pump is installed with the compression tank connection on the suction side of the pump
in a closed loop system. The static pressure is 15 psig and the pump delivers 60 feet of
head when running. With the pump running, the discharge gage would read _____ psig, and
the suction gage would read _____ psig. (round the answers to the nearest whole number)
Correct Answer: 41, 15
Question 5.
A recommended grout mixture is one part cement to ___ part(s) clean, sharp sand, wet
enough to flow freely.
Correct Answer: two
Question 6.
A section of straight pipe should never be installed between the suction side of a pump
and first elbow.
Correct Answer: False
Question 7.
A suction diffuser acts as a high pressure drop device that can be installed at the pump
suction.
Correct Answer: False
, Question 8.
A wet rotor circulator uses system fluid for lubrication.
Correct Answer: True
Question 9.
A(n) ___ impeller is an impeller that has shrouds on both sides of the vanes.
Correct Answer: closed
Question 10.
A(n) ___ is the pump casing or body that contains the pumped HTF under pressure.
Correct Answer: volute
Question 11.
A(n) ____________________ is a device through which an external source of power is used to
apply a force to a fluid in order to move the fluid from one place to another.
Correct Answer: pump
Question 12.
A(n) ____________________ valve is a valve designed to regulate the rate of fluid flow
through a hydronic piping system to meet system requirements.
Correct Answer: balancing
Question 13.
All low-head pumps must pump away from the point of no pressure change.
Correct Answer: False
Question 14.
All-bronze pumps are used for recirculation lines in domestic hot water systems and for
pumping hot process water.
Correct Answer: True
Question 15.
Although ____________________ pumps have the advantage of being able to provide very
high pressures, they discharge fluids in a pulsating flow.
Correct Answer: reciprocating
Question 16.
As an impeller rotates, a low-pressure area is created at the eye of the impeller to allow
fluid to enter the suction side of the pump.
Correct Answer: True