OSHA 511 Final Test General Industry
Questions and Correct Answers Graded
A+ 100% Complete Guaranteed Verified
by Experts
1. Section 11- Judicial review: 11 (c) Prohibits discrimination against employees filing
complaints under OSHA, or for disclosing safety and health issues concerning the workplace.
i. Key word- Whistle Blower Act
2. Horizontal and Vertical Standards: a. Horizontal - everyone is covered
i. Key word - applies to any/all employer in any industry ("general or "across the board")
b. Vertical - Welding is an example of vertical standards
i. Key word- applies to a specific/ particular industry
3. Incorporation by Reference: a. OSHA Directives- Compliance directives - guide book
i. Enforcement and Compliance Directives (CPL)
ii. Letters of Interpretation
iii. Federal Register
4. Definitions 1910.21: a. "Floor Hole" an opening less than 12" but more than 1 inch in its
dimension, in any floor, platform, pavement or yard, through which materials but not persons may
1/
9
, fall; such as a belt hole, pipe opening or slot opening.
b. "Floor Opening" an opening measuring 12 inches or MORE in its dimension
i. Key word - an OPENING is larger than a HOLE
5. Fixed Industrial stairs: a. Egress route for a staircase platforms must be 28" min
6. Osha certifies that a citation must be: a. Addressed and corrections must be
completed by the
abatement date
b. OSHA has 180 days to issue citation
7. Cages or Wells 1910.27 (d) (1): a. Cages or wells shall be provided on Ladders more than
20 feet to a maximum unbroken length of 30 feet.
8. Section 5 (a) (1) of the Act: a. Every employer shall furnish to his employee's employment
and a place of employment which are free from recognized hazards that are causing or likely to cause
death or serious physical harm to his employees.
i. Key word - General Duty Clause
9. OSHA inspection Priority Review: 1st Imminent
danger 2nd Catastrophes and fatal accidents
3rd Employee complaints and referrals
4th Programmed High- Hazard
Inspections 5th Follow up Inspections
2/
9
Questions and Correct Answers Graded
A+ 100% Complete Guaranteed Verified
by Experts
1. Section 11- Judicial review: 11 (c) Prohibits discrimination against employees filing
complaints under OSHA, or for disclosing safety and health issues concerning the workplace.
i. Key word- Whistle Blower Act
2. Horizontal and Vertical Standards: a. Horizontal - everyone is covered
i. Key word - applies to any/all employer in any industry ("general or "across the board")
b. Vertical - Welding is an example of vertical standards
i. Key word- applies to a specific/ particular industry
3. Incorporation by Reference: a. OSHA Directives- Compliance directives - guide book
i. Enforcement and Compliance Directives (CPL)
ii. Letters of Interpretation
iii. Federal Register
4. Definitions 1910.21: a. "Floor Hole" an opening less than 12" but more than 1 inch in its
dimension, in any floor, platform, pavement or yard, through which materials but not persons may
1/
9
, fall; such as a belt hole, pipe opening or slot opening.
b. "Floor Opening" an opening measuring 12 inches or MORE in its dimension
i. Key word - an OPENING is larger than a HOLE
5. Fixed Industrial stairs: a. Egress route for a staircase platforms must be 28" min
6. Osha certifies that a citation must be: a. Addressed and corrections must be
completed by the
abatement date
b. OSHA has 180 days to issue citation
7. Cages or Wells 1910.27 (d) (1): a. Cages or wells shall be provided on Ladders more than
20 feet to a maximum unbroken length of 30 feet.
8. Section 5 (a) (1) of the Act: a. Every employer shall furnish to his employee's employment
and a place of employment which are free from recognized hazards that are causing or likely to cause
death or serious physical harm to his employees.
i. Key word - General Duty Clause
9. OSHA inspection Priority Review: 1st Imminent
danger 2nd Catastrophes and fatal accidents
3rd Employee complaints and referrals
4th Programmed High- Hazard
Inspections 5th Follow up Inspections
2/
9
