ICML LUBRICATION MLT LEVEL II |ACTUAL
QUESTIONS AND VERIFIED ANSWERS|BRAND NEW
2026-2027 UPDATE|GRADED A+
Question 1
"""What is one of the ways to eliminate factors that lead to machine failure? (Ref:1.5a)
A. Hire more mechanics
B. Focus on condition improvement and defect elimination.
C. Increase planned work.
D. Both B & C""
"
CORRECT ANSWER
D
Question 2
"""Where would one likely find a permanently installed machine condition monitoring
system? (Ref:1.100)
A. High speed machinery
B. Machines that degrade very quickly when they begin to degrade
C. Highly Critical, low speed, low load machine
D. All of the above
""
"
CORRECT ANSWER
D
1
,Question 3
"Which of the following depends on operators and maintenance technicians to work
together to maintain long term productive capability of the machine? (Ref:no slide)
A. Run to Failure (RTF)
B. Planned Preventive Maintenance (PPM)
C. Planned Predictive Maintenance (PDM)
D. Reliability Centered Maintenance (RCM)
"
CORRECT ANSWER
C
Question 4
"Which of the following is not a Maintenance Strategy? (Ref:1.60)
A. Persuasive
B. Predictive
C. Proactive
D. Preventative
"
CORRECT ANSWER
A
Question 5
"Which of the following economic realities drove manufacturers initially toward a need for
more advanced maintenance management? (Ref:1.80)
A. Manufacturing labor shortages, which led to mechanization of processes
2
,B. Development of the jet aircraft
C. Increasing consumer demand which led to increases in productivity requirements
D. Growth of nuclear power generation industry
"
CORRECT ANSWER
A
Question 6
"According to E. Rabinowicz, MIT, to what extent are combined abrasive and adhesive
wear responsible for machine degradation (Ref:no slide)
""A. 15 Percent
B. 25 percent
C. 45 percent
D. 75 Percent""
"
CORRECT ANSWER
C
Question 7
"All machine component movement can be described as which of the following? (Ref:2.30)
A. Surface friction
B. Surface contact
C. Fluid Friction
D. Sliding or rolling contact"
CORRECT ANSWER
D
3
, Question 8
"EHL conditions occur primarily in (Ref:2.360)
A. Rolling bearings, gears and cams
B. Slow moving pins and bushings
C. Piston rings and liners
D. Journal bearings"
CORRECT ANSWER
A
Question 9
"If the oil was to approach a solid state under pressure, which of the following would be
true? (Ref:2.360)
A. Fluid friction would be eliminated
B. Higher fluid friction would be created
C. Lower fluid friction would be produced
D. All of the above"
CORRECT ANSWER
B
Question 10
"Tribology is the study of which 3 areas of knowledge? (Ref:2.210)
A. Chemical, mechanical, electrical
B. Surface finish, adhesion, wear
4
QUESTIONS AND VERIFIED ANSWERS|BRAND NEW
2026-2027 UPDATE|GRADED A+
Question 1
"""What is one of the ways to eliminate factors that lead to machine failure? (Ref:1.5a)
A. Hire more mechanics
B. Focus on condition improvement and defect elimination.
C. Increase planned work.
D. Both B & C""
"
CORRECT ANSWER
D
Question 2
"""Where would one likely find a permanently installed machine condition monitoring
system? (Ref:1.100)
A. High speed machinery
B. Machines that degrade very quickly when they begin to degrade
C. Highly Critical, low speed, low load machine
D. All of the above
""
"
CORRECT ANSWER
D
1
,Question 3
"Which of the following depends on operators and maintenance technicians to work
together to maintain long term productive capability of the machine? (Ref:no slide)
A. Run to Failure (RTF)
B. Planned Preventive Maintenance (PPM)
C. Planned Predictive Maintenance (PDM)
D. Reliability Centered Maintenance (RCM)
"
CORRECT ANSWER
C
Question 4
"Which of the following is not a Maintenance Strategy? (Ref:1.60)
A. Persuasive
B. Predictive
C. Proactive
D. Preventative
"
CORRECT ANSWER
A
Question 5
"Which of the following economic realities drove manufacturers initially toward a need for
more advanced maintenance management? (Ref:1.80)
A. Manufacturing labor shortages, which led to mechanization of processes
2
,B. Development of the jet aircraft
C. Increasing consumer demand which led to increases in productivity requirements
D. Growth of nuclear power generation industry
"
CORRECT ANSWER
A
Question 6
"According to E. Rabinowicz, MIT, to what extent are combined abrasive and adhesive
wear responsible for machine degradation (Ref:no slide)
""A. 15 Percent
B. 25 percent
C. 45 percent
D. 75 Percent""
"
CORRECT ANSWER
C
Question 7
"All machine component movement can be described as which of the following? (Ref:2.30)
A. Surface friction
B. Surface contact
C. Fluid Friction
D. Sliding or rolling contact"
CORRECT ANSWER
D
3
, Question 8
"EHL conditions occur primarily in (Ref:2.360)
A. Rolling bearings, gears and cams
B. Slow moving pins and bushings
C. Piston rings and liners
D. Journal bearings"
CORRECT ANSWER
A
Question 9
"If the oil was to approach a solid state under pressure, which of the following would be
true? (Ref:2.360)
A. Fluid friction would be eliminated
B. Higher fluid friction would be created
C. Lower fluid friction would be produced
D. All of the above"
CORRECT ANSWER
B
Question 10
"Tribology is the study of which 3 areas of knowledge? (Ref:2.210)
A. Chemical, mechanical, electrical
B. Surface finish, adhesion, wear
4
