CWEA E/I LEVEL 3 EXAM REAL EXAM 2026 | ALL
QUESTIONS AND CORRECT ANSWERS | VERIFIED
ANSWERS | BRAND NEW VERSION
A 3 phase motor shows 15 FLA.(Full Load Amperes) You have readings
of 15.6, 16.1 and 15.9, what is the condition of the motor? ------------
Correct Answer--------------------The motor is ovearloaded.
4-20 mA output for a device with a range of 0-63,535. Read is 6 mA.
What is the measurement reading? ------------Correct Answer---------------
-----7941.875
Ladder Diagram ------------Correct Answer--------------------Ladder
diagrams are specialized schematics commonly used to document
industrial control logic systems(PLCs).
They are called "ladder" diagrams because they resemble a ladder, with
two vertical rails (supply power) and as many "rungs" (horizontal lines)
as there are control circuits to represent.
How to measure 4-20ma with a digital multi meter(dmm). ------------
Correct Answer--------------------Disconnect one wire of the loop and
connect the DMM in series.
,How far from the disconnect should a pump be located? ------------
Correct Answer--------------------within sight and not at a distance greater
than (50 ft) from equipment.
The most important requirement for good
maintenance of motor starters is: ------------Correct Answer-----------------
---proper lubrication
A reversing starter reverses a three-phase
motor by interchanging: ------------Correct Answer--------------------Any
two of the phases
What kind of protection is provided in a manual across-the-line three-
phase motor control? ------------Correct Answer--------------------Overload
protection only
The drawing that provides a view of the entire
, system in process control is the: ------------Correct Answer-------------------
-P&ID also known as pipping and instrument drawing
The most commonly used type of diagram in
process control is: ------------Correct Answer--------------------piping and
instrument drawing
When Taking a flow measurement the measuring device is performing
what type of calculation? ------------Correct Answer--------------------Root
mean square
A 480V, 3 phase motor, Delta connected, has one leg shorted, what will
the resistance be compared to the other legs ------------Correct Answer--
------------------Lower
A 12V battery rated to provide 1amp for 20 hours across a 2000w load.
How long will the battery continue to produce an output? ------------
Correct Answer--------------------100 hour
QUESTIONS AND CORRECT ANSWERS | VERIFIED
ANSWERS | BRAND NEW VERSION
A 3 phase motor shows 15 FLA.(Full Load Amperes) You have readings
of 15.6, 16.1 and 15.9, what is the condition of the motor? ------------
Correct Answer--------------------The motor is ovearloaded.
4-20 mA output for a device with a range of 0-63,535. Read is 6 mA.
What is the measurement reading? ------------Correct Answer---------------
-----7941.875
Ladder Diagram ------------Correct Answer--------------------Ladder
diagrams are specialized schematics commonly used to document
industrial control logic systems(PLCs).
They are called "ladder" diagrams because they resemble a ladder, with
two vertical rails (supply power) and as many "rungs" (horizontal lines)
as there are control circuits to represent.
How to measure 4-20ma with a digital multi meter(dmm). ------------
Correct Answer--------------------Disconnect one wire of the loop and
connect the DMM in series.
,How far from the disconnect should a pump be located? ------------
Correct Answer--------------------within sight and not at a distance greater
than (50 ft) from equipment.
The most important requirement for good
maintenance of motor starters is: ------------Correct Answer-----------------
---proper lubrication
A reversing starter reverses a three-phase
motor by interchanging: ------------Correct Answer--------------------Any
two of the phases
What kind of protection is provided in a manual across-the-line three-
phase motor control? ------------Correct Answer--------------------Overload
protection only
The drawing that provides a view of the entire
, system in process control is the: ------------Correct Answer-------------------
-P&ID also known as pipping and instrument drawing
The most commonly used type of diagram in
process control is: ------------Correct Answer--------------------piping and
instrument drawing
When Taking a flow measurement the measuring device is performing
what type of calculation? ------------Correct Answer--------------------Root
mean square
A 480V, 3 phase motor, Delta connected, has one leg shorted, what will
the resistance be compared to the other legs ------------Correct Answer--
------------------Lower
A 12V battery rated to provide 1amp for 20 hours across a 2000w load.
How long will the battery continue to produce an output? ------------
Correct Answer--------------------100 hour
