AMPP CIP LEVEL 1 TIPS SET ANSWERS AND
QUESTIONS SET A+
✔✔How to calculate material consumption - ✔✔S.E.D.S (SBV,Effeciency,DFT,SQFT)
multiply,multiply,divide,divide
✔✔Environmental conditions - ✔✔Surface temperature, air, temperature, relative
humidity, dewpoint, wind speed
✔✔ASTM - D3276 - ✔✔Standard guide for painting, inspectors of metal substrates
✔✔Iso 8502/SSPC guide 15 - ✔✔Use of salt, contamination meters
✔✔Salt testing types - ✔✔Bresle patch
Latex sleeve
CSN test kit
Potassium Ferricyanide test
Salt contamination meter
✔✔What method is used to test for the presence of nitrates? - ✔✔Ion test strips
✔✔Bresel patch methods - ✔✔10 minutes on surface and reinject water four times
✔✔Potassium ferrocyanide - ✔✔Ensure test site is clean, missed the surface with
distilled water, apply the indication paper, look for dark blue spots
✔✔Sleeve salt test - ✔✔Put sleeve onto surface, put Clorox in, rub for two minutes,
titration tube in
✔✔Types of surface profile checking - ✔✔Surface profile comparators, digital profile
gauges, replica tape
✔✔ASTM - D 4417 - ✔✔Test methods for field measurement of surface profile of blast
clean steel
, ✔✔SSPC-PA2 - ✔✔Procedure for determining conformance to Dry coating thickness
requirements.
✔✔ISO 19840 - ✔✔Measurement of, and acceptance criteria for, the thickness of dry
films on rough surfaces
✔✔What is an advantage of using a magnetic pull off gauge? - ✔✔It is intrinsically safe
✔✔What is the minimum distance from the edge that you can reliably take a
measurement using a magnetic pull off gauge - ✔✔1 inch
✔✔NACE SPO188 - ✔✔Discontinuity (Holiday) Testing of New Protective Coatings on
Conductive Substrates
✔✔How much water do you put on a low-voltage sponge tester? - ✔✔1 ounce per
gallon
✔✔Holiday testing only works with? - ✔✔Nonconductive coatings applied to conductive
substrates
✔✔At what height is fall protection equipment required - ✔✔6 feet
✔✔ASTM - D 5162 - ✔✔Standard practice for discontinuity holiday testing of
nonconductive protective coating on metallic substrates
✔✔Iso 2808 - ✔✔Paints and varnishes — determination of film thickness
✔✔Three types of measuring film thickness - ✔✔WFT comb gauge, type one DFT
gauge, type 2DFT gauge(digital)
✔✔SSPC-VIS 3 - ✔✔Guide and Reference Photographs for Steel Surfaces Prepared
by Hand and Power Tool Cleaning
✔✔ Primary purpose of applying industrial coatings - ✔✔Applying industrial coatings is
to prevent or limit contact between a metal substrate and it's corrosive environment
✔✔Four reasons for coating - ✔✔Aesthetics, performance requirements, safety
identification, corrosion prevention and control
✔✔Definition for corrosion - ✔✔Deterioration of a metal or alloy that results from an
electrochemical reaction with its environment
✔✔A.C.M.E - ✔✔Anode,Cathode,Metallic pathway, electrolyte
QUESTIONS SET A+
✔✔How to calculate material consumption - ✔✔S.E.D.S (SBV,Effeciency,DFT,SQFT)
multiply,multiply,divide,divide
✔✔Environmental conditions - ✔✔Surface temperature, air, temperature, relative
humidity, dewpoint, wind speed
✔✔ASTM - D3276 - ✔✔Standard guide for painting, inspectors of metal substrates
✔✔Iso 8502/SSPC guide 15 - ✔✔Use of salt, contamination meters
✔✔Salt testing types - ✔✔Bresle patch
Latex sleeve
CSN test kit
Potassium Ferricyanide test
Salt contamination meter
✔✔What method is used to test for the presence of nitrates? - ✔✔Ion test strips
✔✔Bresel patch methods - ✔✔10 minutes on surface and reinject water four times
✔✔Potassium ferrocyanide - ✔✔Ensure test site is clean, missed the surface with
distilled water, apply the indication paper, look for dark blue spots
✔✔Sleeve salt test - ✔✔Put sleeve onto surface, put Clorox in, rub for two minutes,
titration tube in
✔✔Types of surface profile checking - ✔✔Surface profile comparators, digital profile
gauges, replica tape
✔✔ASTM - D 4417 - ✔✔Test methods for field measurement of surface profile of blast
clean steel
, ✔✔SSPC-PA2 - ✔✔Procedure for determining conformance to Dry coating thickness
requirements.
✔✔ISO 19840 - ✔✔Measurement of, and acceptance criteria for, the thickness of dry
films on rough surfaces
✔✔What is an advantage of using a magnetic pull off gauge? - ✔✔It is intrinsically safe
✔✔What is the minimum distance from the edge that you can reliably take a
measurement using a magnetic pull off gauge - ✔✔1 inch
✔✔NACE SPO188 - ✔✔Discontinuity (Holiday) Testing of New Protective Coatings on
Conductive Substrates
✔✔How much water do you put on a low-voltage sponge tester? - ✔✔1 ounce per
gallon
✔✔Holiday testing only works with? - ✔✔Nonconductive coatings applied to conductive
substrates
✔✔At what height is fall protection equipment required - ✔✔6 feet
✔✔ASTM - D 5162 - ✔✔Standard practice for discontinuity holiday testing of
nonconductive protective coating on metallic substrates
✔✔Iso 2808 - ✔✔Paints and varnishes — determination of film thickness
✔✔Three types of measuring film thickness - ✔✔WFT comb gauge, type one DFT
gauge, type 2DFT gauge(digital)
✔✔SSPC-VIS 3 - ✔✔Guide and Reference Photographs for Steel Surfaces Prepared
by Hand and Power Tool Cleaning
✔✔ Primary purpose of applying industrial coatings - ✔✔Applying industrial coatings is
to prevent or limit contact between a metal substrate and it's corrosive environment
✔✔Four reasons for coating - ✔✔Aesthetics, performance requirements, safety
identification, corrosion prevention and control
✔✔Definition for corrosion - ✔✔Deterioration of a metal or alloy that results from an
electrochemical reaction with its environment
✔✔A.C.M.E - ✔✔Anode,Cathode,Metallic pathway, electrolyte
