TPC 108 UPDATED ACTUAL QUESTIONS AND CORRECT
ANSWERS
Question:
1. The purpose of a right-angle adapter is to enable drilling
• For long periods of time
• Blind holes
• Hardwoods In close quarters
Answer:
In close quarters
Question:
2. The shank of a drill bit is held in the
• Chuck
• Grip
• Nozzie
• Suction cup
Answer:
Chuck
Question:
3. If you are drilling a hole all the way through a workpiece, you should ease up on the pressure when the
bit
Is halfway through the work
• Nears the other side
• Sends chips out of the hole Touches the work
Answer:
Nears the other side
Question:
4. You should use a jig when
• A right-angle adapter is not available O Drilling a blind hole Drilling at an angle
• Drilling at high speeds
Answer:
Drilling at an angle
Question:
5. You can prevent electric shocks from power tools by
• Grounding them O Pulling out the grounding prongs
• Using two-hole outlets
• Working carefully
Answer:
Grounding them
, Question:
6. A carbide-tipped core bit is used for boring holes________in diameter.
• Smaller than ^1/_2 in.
• Between ^1/_2 and 1*11 2 in.
• Between 1^1/ 2 and 3^1/2 in.
• Larger than 3^1/_2 in.
Answer:
• Between 1^1/ 2 and 3^1/2 in.
Question:
7. When drilling with a diamond-aggregate core bit, you must use a special rotary hammer and a
• Depth gauge.
• Stand
• Starter bit
• Voltmeter
Answer:
Stand
Question:
8. Which of the following is useful in maintaining the proper pressure and drilling speed when using an
electric hammer?
• Ammeter
• Depth gauge
• Ohmmeter
• Voltmeter.
Answer:
Ammeter
Question:
9. When using an electric hammer, always wear
• Ear plugs
• Finger guards
• Gloves
• Safety glasses
Answer:
• Safety glasses
Question:
10. What should never be removed from a three-prong plug?
• Adapter plug
• Grounding prong
• Hang tag
• UL-approved label
Answer:
• Grounding prong
ANSWERS
Question:
1. The purpose of a right-angle adapter is to enable drilling
• For long periods of time
• Blind holes
• Hardwoods In close quarters
Answer:
In close quarters
Question:
2. The shank of a drill bit is held in the
• Chuck
• Grip
• Nozzie
• Suction cup
Answer:
Chuck
Question:
3. If you are drilling a hole all the way through a workpiece, you should ease up on the pressure when the
bit
Is halfway through the work
• Nears the other side
• Sends chips out of the hole Touches the work
Answer:
Nears the other side
Question:
4. You should use a jig when
• A right-angle adapter is not available O Drilling a blind hole Drilling at an angle
• Drilling at high speeds
Answer:
Drilling at an angle
Question:
5. You can prevent electric shocks from power tools by
• Grounding them O Pulling out the grounding prongs
• Using two-hole outlets
• Working carefully
Answer:
Grounding them
, Question:
6. A carbide-tipped core bit is used for boring holes________in diameter.
• Smaller than ^1/_2 in.
• Between ^1/_2 and 1*11 2 in.
• Between 1^1/ 2 and 3^1/2 in.
• Larger than 3^1/_2 in.
Answer:
• Between 1^1/ 2 and 3^1/2 in.
Question:
7. When drilling with a diamond-aggregate core bit, you must use a special rotary hammer and a
• Depth gauge.
• Stand
• Starter bit
• Voltmeter
Answer:
Stand
Question:
8. Which of the following is useful in maintaining the proper pressure and drilling speed when using an
electric hammer?
• Ammeter
• Depth gauge
• Ohmmeter
• Voltmeter.
Answer:
Ammeter
Question:
9. When using an electric hammer, always wear
• Ear plugs
• Finger guards
• Gloves
• Safety glasses
Answer:
• Safety glasses
Question:
10. What should never be removed from a three-prong plug?
• Adapter plug
• Grounding prong
• Hang tag
• UL-approved label
Answer:
• Grounding prong
