Electrical Job Information Test bank
Study online at https://quizlet.com/_eskfob
1. Rings and Jewelry worn on the job a hazard
are _______________ to an electrical
worker.
2. A keen sense of what to do or say tact
to maintain good relations or avoid
offense.
3. Slight shock felt; not painful but dis- 5 mA
turbing. Average individual can let
go. Strong involuntary reactions can
lead to other injuries. These reac-
tions best describe a current of ? .
4. Extreme pain, respiratory arrest, se- 50 mA
vere muscular contractions. Death
is possible. These reactions best de-
scribe a current from ? to 150 mil-
liamperes.
5. Fuses and Circuit Breakers are de- conductors and equipment
signed to protect ___________.
6. No employer shall permit an em- 1. the employee is protected against shock by deen-
ployee to work in such proximity to ergizing the circuit.
any part of an electric power circuit 2. grounding the deenergized circuit
that the employee could contact the 3. by guarding it effectively by insulation or other
electric power in the course of work means
unless ______________?
7. Before work is begun, the employer shall
_____________ ascertain by inquiry or
direct observation whether any part
, Electrical Job Information Test bank
Study online at https://quizlet.com/_eskfob
of an energize electric power circuit
is located in a place that could cause
direct contact with that circuit.
8. the employer __________ post and shall
maintain proper warning signs
where an energized electric circuit
exist.
9. the employer _______________ advise shall
employees of the location of ener-
gized electric circuits, the hazards in-
volved, and the protective measures
to be taken.
10. ANSI defines "FAMILIARIZATION" of False
MEWPs as: "Instructions to enable
the trainee to become a qualified
person regarding the task to be
performed, including knowledge re-
garding potential hazards."
11. ________________ are essentially lad- Aerial work platforms
der replacements. They are a type
of small lift that can easily be set up
by one person. They are generally a
"push around" type of lift.
12. _____________ are a type of aerial work Boom lifts
platform that is attached to exten-
sion arms that are recessed within
one another - like a refractor style of
telescope.
, Electrical Job Information Test bank
Study online at https://quizlet.com/_eskfob
13. _____________ are a type of aerial work vertical mast lifts
platform that are able to fit into tight
spaces because their design gener-
ally allows for a small footprint.
14. Which of the following lifts are con- Scissor lifts
sidered scaffolding?
15. which type of "push around" type Aerial work platforms
of lift is essentially a ladder replace-
ment?
16. To prevent the work platform boards be cleated on the underside
from slipping off rolling scaffolds,
they should ? .
17. when erecting a scaffold, use adjusting screws
____________ instead of blocking to
adjust to uneven grade conditions.
18. a permit-required confined space 1. contains or has the potential to contain a haz-
(permit space) is a confined space ardous atmosphere.
that ____________________? 2. contains a material that has a potential for engulf-
ing an entrant
3. has an internal configuration such that an entrant
could be trapped or asphyxiated by inwardly con-
verging walls or by a floor which slopes downward
and tapers to a smaller cross section
19. A(n) _______________ is an individual attendant
stationed outside one or more per-
mit spaces who monitors conditions
Study online at https://quizlet.com/_eskfob
1. Rings and Jewelry worn on the job a hazard
are _______________ to an electrical
worker.
2. A keen sense of what to do or say tact
to maintain good relations or avoid
offense.
3. Slight shock felt; not painful but dis- 5 mA
turbing. Average individual can let
go. Strong involuntary reactions can
lead to other injuries. These reac-
tions best describe a current of ? .
4. Extreme pain, respiratory arrest, se- 50 mA
vere muscular contractions. Death
is possible. These reactions best de-
scribe a current from ? to 150 mil-
liamperes.
5. Fuses and Circuit Breakers are de- conductors and equipment
signed to protect ___________.
6. No employer shall permit an em- 1. the employee is protected against shock by deen-
ployee to work in such proximity to ergizing the circuit.
any part of an electric power circuit 2. grounding the deenergized circuit
that the employee could contact the 3. by guarding it effectively by insulation or other
electric power in the course of work means
unless ______________?
7. Before work is begun, the employer shall
_____________ ascertain by inquiry or
direct observation whether any part
, Electrical Job Information Test bank
Study online at https://quizlet.com/_eskfob
of an energize electric power circuit
is located in a place that could cause
direct contact with that circuit.
8. the employer __________ post and shall
maintain proper warning signs
where an energized electric circuit
exist.
9. the employer _______________ advise shall
employees of the location of ener-
gized electric circuits, the hazards in-
volved, and the protective measures
to be taken.
10. ANSI defines "FAMILIARIZATION" of False
MEWPs as: "Instructions to enable
the trainee to become a qualified
person regarding the task to be
performed, including knowledge re-
garding potential hazards."
11. ________________ are essentially lad- Aerial work platforms
der replacements. They are a type
of small lift that can easily be set up
by one person. They are generally a
"push around" type of lift.
12. _____________ are a type of aerial work Boom lifts
platform that is attached to exten-
sion arms that are recessed within
one another - like a refractor style of
telescope.
, Electrical Job Information Test bank
Study online at https://quizlet.com/_eskfob
13. _____________ are a type of aerial work vertical mast lifts
platform that are able to fit into tight
spaces because their design gener-
ally allows for a small footprint.
14. Which of the following lifts are con- Scissor lifts
sidered scaffolding?
15. which type of "push around" type Aerial work platforms
of lift is essentially a ladder replace-
ment?
16. To prevent the work platform boards be cleated on the underside
from slipping off rolling scaffolds,
they should ? .
17. when erecting a scaffold, use adjusting screws
____________ instead of blocking to
adjust to uneven grade conditions.
18. a permit-required confined space 1. contains or has the potential to contain a haz-
(permit space) is a confined space ardous atmosphere.
that ____________________? 2. contains a material that has a potential for engulf-
ing an entrant
3. has an internal configuration such that an entrant
could be trapped or asphyxiated by inwardly con-
verging walls or by a floor which slopes downward
and tapers to a smaller cross section
19. A(n) _______________ is an individual attendant
stationed outside one or more per-
mit spaces who monitors conditions
