The a+ advanTage: ace 2026/2027
neIeP 600 fInal examInaTIon wITh
ThIs sTudy guIde comPrehensIve
q&a
◉ 4v Answer: Refer to figure 1. The zener diode is designed to
breakdown at 6VDC what is the voltage drop across R1 with a constant
DC supply of 10VDC
◉ 30 rpm Answer: An elevators motor rotates at 1200 rpm at contract
speed and is geard at a ratio of 40:1. If the motor turns 40 rpm the
sheave turns 1 rpm. What is the actual speed of the drive sheave in
rpms?
◉ The output will go to zero Answer: Refer to figure 2. For the
comparator circuit shown, what will happen to the output of the
noninverting input goes more positive than the inverting input?
◉ -20 mv Answer: Refer to figure 3. For the inverting op amp shown,
what is the output voltage?
◉ Saturation Answer: Which term defines the limit of magnetic strength
around an inductor even though the current through the coil increases
◉ Voltage is removed from anode to cathode Answer: Which of the
following describes how an SCR is turned OFF?
◉ Top right Answer: On the fourteen pin DIP IC shown in figure 4 what
is the location of pin 14
, ◉ 1507 ohms Answer: A brake coil has an inductance of 4 henries. If the
coil was placed into a circuit with an operating frequency of 60hz the
coil would have a resistance of:
◉ light Answer: The photodiode will conduct current when it detects
◉ A relay timer Answer: What does the circuit in figure 5 represent?
◉ 12.5 A Answer: A string of temporary lighting has fifteen 100 watt
bulbs. A 15 amp breaker is the maximum size that can be used with the
14 gauge wire used in this 120 volt circuit. What is the current?
◉ 4.61 henries Answer: If a circuit has three inductors in parallel of 10,
15, and 20 henries, what is the total inductance?
◉ LED Answer: What does the symbol in figure 6 represent?
◉ A .7V drop from base-to-emitter is an indication of a good junction
Answer: Which of the following statements is correct when testing
transistors?
An SCR Answer: What does the symbol shown below represent?
◉ 5 seconds Answer: What is the length of time required to charge a
500-microfarad capacitor in series with a 10K ohm resistor to the
maximum applied voltage of 125 VDC? (TC = R x C)
neIeP 600 fInal examInaTIon wITh
ThIs sTudy guIde comPrehensIve
q&a
◉ 4v Answer: Refer to figure 1. The zener diode is designed to
breakdown at 6VDC what is the voltage drop across R1 with a constant
DC supply of 10VDC
◉ 30 rpm Answer: An elevators motor rotates at 1200 rpm at contract
speed and is geard at a ratio of 40:1. If the motor turns 40 rpm the
sheave turns 1 rpm. What is the actual speed of the drive sheave in
rpms?
◉ The output will go to zero Answer: Refer to figure 2. For the
comparator circuit shown, what will happen to the output of the
noninverting input goes more positive than the inverting input?
◉ -20 mv Answer: Refer to figure 3. For the inverting op amp shown,
what is the output voltage?
◉ Saturation Answer: Which term defines the limit of magnetic strength
around an inductor even though the current through the coil increases
◉ Voltage is removed from anode to cathode Answer: Which of the
following describes how an SCR is turned OFF?
◉ Top right Answer: On the fourteen pin DIP IC shown in figure 4 what
is the location of pin 14
, ◉ 1507 ohms Answer: A brake coil has an inductance of 4 henries. If the
coil was placed into a circuit with an operating frequency of 60hz the
coil would have a resistance of:
◉ light Answer: The photodiode will conduct current when it detects
◉ A relay timer Answer: What does the circuit in figure 5 represent?
◉ 12.5 A Answer: A string of temporary lighting has fifteen 100 watt
bulbs. A 15 amp breaker is the maximum size that can be used with the
14 gauge wire used in this 120 volt circuit. What is the current?
◉ 4.61 henries Answer: If a circuit has three inductors in parallel of 10,
15, and 20 henries, what is the total inductance?
◉ LED Answer: What does the symbol in figure 6 represent?
◉ A .7V drop from base-to-emitter is an indication of a good junction
Answer: Which of the following statements is correct when testing
transistors?
An SCR Answer: What does the symbol shown below represent?
◉ 5 seconds Answer: What is the length of time required to charge a
500-microfarad capacitor in series with a 10K ohm resistor to the
maximum applied voltage of 125 VDC? (TC = R x C)
