• NCCER Core Final 09/01/2026
Exam
NCCER Core Final Exam 1 Study Guide
(2026/2027) – Practice Questions and Verified
Answers
Convert 1/4 to its decimal equivalent.
A) .01
B) .25
C) 0.4
D) 0.5 - Correct Answer :B
Piping that is field-routed to a pump must be supported
A) Off the pump suction
P 1
, • NCCER Core Final 09/01/2026
Exam
B) Diagonally
C) Independently
D) Off the pump discharge - Correct Answer :C
What is used when lighting a cutting torch ?
A) Striker
B) Cigarette lighter
C) Match
D) Any open flame - Correct Answer :A
Where is specific information needed to install piping and associated items found ?
A) Reliability network
B) Owner of the company
C) Material Manufacturer
D) Standards and Specifications - Correct Answer :D
Damaged and broken tools should be
A) Used if possible
B) Kept for backup
C) Taken out of Service
D) Used for minor tasks - Correct Answer :C
What is the ID of 10'' schedule 80 piping.
A) 9 3/16
B) 9 5/16
C) 9 9/16
P 2
, • NCCER Core Final 09/01/2026
Exam
D) 10 1/16 - Correct Answer :C
The two steps in making up threaded joints are the hand engagement and
A) Machine makeup
B) Wrench makeup
C) Driver makeup - Correct Answer :B
Which of the following actions should be taken before a hydrostatic test is performed ?
A) Remove pressure relief valves
B) Leave control mechanisms in place
C) Leave orifice flanges in place
D) Remove blinds - Correct Answer :a
A 4-inch lateral riser is to be fabricated for a 6-inch pipe. How many ordinate lines will
be needed to lay out this cut ?
A) 32
B) 16
C) 8
D) 4 - Correct Answer :C
Who is qualified to repair power tools.
A) Journey person
B) Competent Technician
C) Electrician
D) Tool crib attendant - Correct Answer :B
P 3
, • NCCER Core Final 09/01/2026
Exam
Which of the following plastic pipes is NOT joined by solvent welding ?
A) PVC
B) HDPE
C) CPVC
D) ABS - Correct Answer :B
Material placed in the bottom of the trench under the pipe to provide support is called.
A) Heave
B) Sub trench
C) Trench load
D) Bedding - Correct Answer :D
Socket weld joints have a gap between the end of the pipe and the bottom of the
socket. What is the purpose of this gap ?
A) Makes assembly easier
B) Reduces flexibility at the fitting
C) Prevents weld cracking
D) Provides fit-up adjustment - Correct Answer :C
When are rupture discs installed into a pipeline?
A) Before flushing and testing of pipeline
B) After installation of the pipeline
C) Before start-up of the system
D) After start-up of the system - Correct Answer :C
Chain come-alongs are PRIMARILY designed for?
P 4
Exam
NCCER Core Final Exam 1 Study Guide
(2026/2027) – Practice Questions and Verified
Answers
Convert 1/4 to its decimal equivalent.
A) .01
B) .25
C) 0.4
D) 0.5 - Correct Answer :B
Piping that is field-routed to a pump must be supported
A) Off the pump suction
P 1
, • NCCER Core Final 09/01/2026
Exam
B) Diagonally
C) Independently
D) Off the pump discharge - Correct Answer :C
What is used when lighting a cutting torch ?
A) Striker
B) Cigarette lighter
C) Match
D) Any open flame - Correct Answer :A
Where is specific information needed to install piping and associated items found ?
A) Reliability network
B) Owner of the company
C) Material Manufacturer
D) Standards and Specifications - Correct Answer :D
Damaged and broken tools should be
A) Used if possible
B) Kept for backup
C) Taken out of Service
D) Used for minor tasks - Correct Answer :C
What is the ID of 10'' schedule 80 piping.
A) 9 3/16
B) 9 5/16
C) 9 9/16
P 2
, • NCCER Core Final 09/01/2026
Exam
D) 10 1/16 - Correct Answer :C
The two steps in making up threaded joints are the hand engagement and
A) Machine makeup
B) Wrench makeup
C) Driver makeup - Correct Answer :B
Which of the following actions should be taken before a hydrostatic test is performed ?
A) Remove pressure relief valves
B) Leave control mechanisms in place
C) Leave orifice flanges in place
D) Remove blinds - Correct Answer :a
A 4-inch lateral riser is to be fabricated for a 6-inch pipe. How many ordinate lines will
be needed to lay out this cut ?
A) 32
B) 16
C) 8
D) 4 - Correct Answer :C
Who is qualified to repair power tools.
A) Journey person
B) Competent Technician
C) Electrician
D) Tool crib attendant - Correct Answer :B
P 3
, • NCCER Core Final 09/01/2026
Exam
Which of the following plastic pipes is NOT joined by solvent welding ?
A) PVC
B) HDPE
C) CPVC
D) ABS - Correct Answer :B
Material placed in the bottom of the trench under the pipe to provide support is called.
A) Heave
B) Sub trench
C) Trench load
D) Bedding - Correct Answer :D
Socket weld joints have a gap between the end of the pipe and the bottom of the
socket. What is the purpose of this gap ?
A) Makes assembly easier
B) Reduces flexibility at the fitting
C) Prevents weld cracking
D) Provides fit-up adjustment - Correct Answer :C
When are rupture discs installed into a pipeline?
A) Before flushing and testing of pipeline
B) After installation of the pipeline
C) Before start-up of the system
D) After start-up of the system - Correct Answer :C
Chain come-alongs are PRIMARILY designed for?
P 4
