TEXAS ELECTRICIAN APPRENTICE
CERTIFICATION EXAM ACTUAL 2026
VERIFIED QUESTIONS WITH ANSWERS
COMPREHENSIVE & RATIONALE|INSTANT
DOWNLOAD
1. In Texas, the primary purpose of registering as an electrician
apprentice is to:
A. Allow independent electrical contracting
B. Perform electrical work only under appropriate supervision while
gaining experience
C. Eliminate licensing requirements
D. Permit electrical inspections
Answer: B. Perform electrical work only under appropriate
supervision while gaining experience
Rationale: An electrician apprentice in Texas is registered to gain
practical experience while working under the supervision of
appropriately licensed electricians. Apprentices cannot perform
unsupervised electrical work or operate independently.
2. Which instrument is most appropriate for verifying the absence of
voltage before beginning electrical work?
A. Clamp meter
B. Non-contact voltage tester followed by a properly rated multimeter
C. Ohmmeter only
D. Megohmmeter
Answer: B. Non-contact voltage tester followed by a properly rated
multimeter
1
,Rationale: Best safety practices require verifying voltage using an
approved tester, then confirming with a properly rated meter following
the "live-dead-live" testing procedure.
3. Which PPE provides the highest level of protection against
electrical arc flash?
A. Cotton gloves
B. Leather boots only
C. Arc-rated clothing with appropriate PPE category
D. Safety glasses only
Answer: C. Arc-rated clothing with appropriate PPE category
Rationale: Arc-rated clothing, face shields, gloves, and other PPE
selected according to incident energy calculations or PPE categories
offer protection from arc flash hazards.
4. What does the grounding conductor primarily accomplish?
A. Increases operating voltage
B. Carries normal load current
C. Provides a low-impedance fault current path
D. Reduces wire size requirements
Answer: C. Provides a low-impedance fault current path
Rationale: Equipment grounding conductors safely conduct fault
current back to the source, allowing overcurrent devices to trip quickly
and reduce shock hazards.
5. Which color is commonly used to identify grounded conductors?
2
,A. Red
B. White or gray
C. Orange
D. Brown
Answer: B. White or gray
Rationale: The NEC identifies white or gray insulation for grounded
(neutral) conductors unless otherwise permitted by specific applications.
6. What is Ohm's Law?
A. P = EI
B. E = IR
C. I = PR
D. R = EI
Answer: B. E = IR
Rationale: Voltage equals current multiplied by resistance. This
relationship is fundamental in electrical troubleshooting and circuit
calculations.
7. A 20-amp branch circuit generally requires what minimum copper
conductor size?
A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
Answer: B. 12 AWG
Rationale: Under typical NEC requirements, 12 AWG copper
conductors are required for 20-amp branch circuits.
3
, 8. Lockout/tagout procedures are intended to:
A. Increase productivity
B. Prevent unexpected energization
C. Improve lighting
D. Reduce voltage drop
Answer: B. Prevent unexpected energization
Rationale: Lockout/tagout protects workers by ensuring equipment
cannot be accidentally energized during servicing.
9. Which device protects people from electrical shock by monitoring
current imbalance?
A. AFCI
B. GFCI
C. Disconnect switch
D. Transformer
Answer: B. GFCI
Rationale: Ground-Fault Circuit Interrupters monitor the difference
between outgoing and returning current and trip rapidly when leakage
is detected.
10. Current is measured in:
A. Volts
B. Ohms
C. Amperes
D. Watts
Answer: C. Amperes
4
CERTIFICATION EXAM ACTUAL 2026
VERIFIED QUESTIONS WITH ANSWERS
COMPREHENSIVE & RATIONALE|INSTANT
DOWNLOAD
1. In Texas, the primary purpose of registering as an electrician
apprentice is to:
A. Allow independent electrical contracting
B. Perform electrical work only under appropriate supervision while
gaining experience
C. Eliminate licensing requirements
D. Permit electrical inspections
Answer: B. Perform electrical work only under appropriate
supervision while gaining experience
Rationale: An electrician apprentice in Texas is registered to gain
practical experience while working under the supervision of
appropriately licensed electricians. Apprentices cannot perform
unsupervised electrical work or operate independently.
2. Which instrument is most appropriate for verifying the absence of
voltage before beginning electrical work?
A. Clamp meter
B. Non-contact voltage tester followed by a properly rated multimeter
C. Ohmmeter only
D. Megohmmeter
Answer: B. Non-contact voltage tester followed by a properly rated
multimeter
1
,Rationale: Best safety practices require verifying voltage using an
approved tester, then confirming with a properly rated meter following
the "live-dead-live" testing procedure.
3. Which PPE provides the highest level of protection against
electrical arc flash?
A. Cotton gloves
B. Leather boots only
C. Arc-rated clothing with appropriate PPE category
D. Safety glasses only
Answer: C. Arc-rated clothing with appropriate PPE category
Rationale: Arc-rated clothing, face shields, gloves, and other PPE
selected according to incident energy calculations or PPE categories
offer protection from arc flash hazards.
4. What does the grounding conductor primarily accomplish?
A. Increases operating voltage
B. Carries normal load current
C. Provides a low-impedance fault current path
D. Reduces wire size requirements
Answer: C. Provides a low-impedance fault current path
Rationale: Equipment grounding conductors safely conduct fault
current back to the source, allowing overcurrent devices to trip quickly
and reduce shock hazards.
5. Which color is commonly used to identify grounded conductors?
2
,A. Red
B. White or gray
C. Orange
D. Brown
Answer: B. White or gray
Rationale: The NEC identifies white or gray insulation for grounded
(neutral) conductors unless otherwise permitted by specific applications.
6. What is Ohm's Law?
A. P = EI
B. E = IR
C. I = PR
D. R = EI
Answer: B. E = IR
Rationale: Voltage equals current multiplied by resistance. This
relationship is fundamental in electrical troubleshooting and circuit
calculations.
7. A 20-amp branch circuit generally requires what minimum copper
conductor size?
A. 14 AWG
B. 12 AWG
C. 10 AWG
D. 8 AWG
Answer: B. 12 AWG
Rationale: Under typical NEC requirements, 12 AWG copper
conductors are required for 20-amp branch circuits.
3
, 8. Lockout/tagout procedures are intended to:
A. Increase productivity
B. Prevent unexpected energization
C. Improve lighting
D. Reduce voltage drop
Answer: B. Prevent unexpected energization
Rationale: Lockout/tagout protects workers by ensuring equipment
cannot be accidentally energized during servicing.
9. Which device protects people from electrical shock by monitoring
current imbalance?
A. AFCI
B. GFCI
C. Disconnect switch
D. Transformer
Answer: B. GFCI
Rationale: Ground-Fault Circuit Interrupters monitor the difference
between outgoing and returning current and trip rapidly when leakage
is detected.
10. Current is measured in:
A. Volts
B. Ohms
C. Amperes
D. Watts
Answer: C. Amperes
4
