BGAS-CSWIP Grade 2 Painting Inspector
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationales 2027 Q&A | Instant
Download Pdf
Q1. What is the primary purpose of a coating system applied to a steel
structure?
A. To increase the weight of the structure
B. To improve electrical conductivity
C. To protect the substrate from corrosion and provide the required service
performance
D. To eliminate the need for inspection
Answer: C. To protect the substrate from corrosion and provide the
required service performance
Rationale: A coating system is primarily designed to protect the substrate
against corrosion and other environmental or service-related degradation
while providing the specified performance.
Q2. Which of the following is normally considered part of a coating system?
A. Primer only
B. Primer, intermediate coat, and finish coat
C. Abrasive only
D. Solvent only
,Answer: B. Primer, intermediate coat, and finish coat
Rationale: A complete protective coating system may consist of several
coats, each serving a particular function such as adhesion, corrosion
protection, barrier protection, or appearance.
Q3. What is the main function of a primer?
A. To provide the final decorative appearance only
B. To improve adhesion and provide initial corrosion protection
C. To remove mill scale
D. To reduce steel thickness
Answer: B. To improve adhesion and provide initial corrosion protection
Rationale: Primers are formulated to adhere to the prepared substrate and
provide a foundation for subsequent coats, often contributing significantly
to corrosion protection.
Q4. What does DFT stand for in coating inspection?
A. Dry Film Thickness
B. Direct Film Temperature
C. Dry Finish Treatment
D. Depth Film Test
Answer: A. Dry Film Thickness
Rationale: DFT is the thickness of a coating after it has dried or cured. It is
a fundamental inspection measurement used to verify compliance with the
coating specification.
,Q5. What does WFT stand for?
A. Wet Film Thickness
B. Water Film Treatment
C. Working Film Temperature
D. Wet Finish Test
Answer: A. Wet Film Thickness
Rationale: WFT is the thickness of a freshly applied wet coating before
significant solvent evaporation or curing occurs.
Q6. Which instrument is commonly used to measure the wet film thickness
of a coating?
A. Surface profile gauge
B. Wet film comb
C. Holiday detector
D. Psychrometer
Answer: B. Wet film comb
Rationale: A wet film thickness comb can be placed into freshly applied
coating to estimate its thickness and help the applicator maintain the
specified application rate.
Q7. What is the principal purpose of measuring surface profile after abrasive
blast cleaning?
A. To determine steel hardness
B. To determine the coating colour
C. To verify that the surface roughness is suitable for the specified coating
, system
D. To determine the ambient air temperature
Answer: C. To verify that the surface roughness is suitable for the specified
coating system
Rationale: Surface profile affects coating adhesion and the amount of
coating required to cover the peaks and valleys. The profile must therefore
comply with the coating specification.
Q8. Which method is commonly used to assess surface profile on blast-
cleaned steel?
A. Replica tape
B. Holiday detector
C. Wet film comb
D. Paint brush
Answer: A. Replica tape
Rationale: Replica tape can reproduce the surface profile and allow the
inspector to measure the resulting replica using an appropriate
micrometer.
Q9. What is the purpose of abrasive blast cleaning?
A. To apply the finish coat
B. To remove contaminants and produce an appropriate surface condition
and profile
C. To increase coating viscosity
D. To cure the coating
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationales 2027 Q&A | Instant
Download Pdf
Q1. What is the primary purpose of a coating system applied to a steel
structure?
A. To increase the weight of the structure
B. To improve electrical conductivity
C. To protect the substrate from corrosion and provide the required service
performance
D. To eliminate the need for inspection
Answer: C. To protect the substrate from corrosion and provide the
required service performance
Rationale: A coating system is primarily designed to protect the substrate
against corrosion and other environmental or service-related degradation
while providing the specified performance.
Q2. Which of the following is normally considered part of a coating system?
A. Primer only
B. Primer, intermediate coat, and finish coat
C. Abrasive only
D. Solvent only
,Answer: B. Primer, intermediate coat, and finish coat
Rationale: A complete protective coating system may consist of several
coats, each serving a particular function such as adhesion, corrosion
protection, barrier protection, or appearance.
Q3. What is the main function of a primer?
A. To provide the final decorative appearance only
B. To improve adhesion and provide initial corrosion protection
C. To remove mill scale
D. To reduce steel thickness
Answer: B. To improve adhesion and provide initial corrosion protection
Rationale: Primers are formulated to adhere to the prepared substrate and
provide a foundation for subsequent coats, often contributing significantly
to corrosion protection.
Q4. What does DFT stand for in coating inspection?
A. Dry Film Thickness
B. Direct Film Temperature
C. Dry Finish Treatment
D. Depth Film Test
Answer: A. Dry Film Thickness
Rationale: DFT is the thickness of a coating after it has dried or cured. It is
a fundamental inspection measurement used to verify compliance with the
coating specification.
,Q5. What does WFT stand for?
A. Wet Film Thickness
B. Water Film Treatment
C. Working Film Temperature
D. Wet Finish Test
Answer: A. Wet Film Thickness
Rationale: WFT is the thickness of a freshly applied wet coating before
significant solvent evaporation or curing occurs.
Q6. Which instrument is commonly used to measure the wet film thickness
of a coating?
A. Surface profile gauge
B. Wet film comb
C. Holiday detector
D. Psychrometer
Answer: B. Wet film comb
Rationale: A wet film thickness comb can be placed into freshly applied
coating to estimate its thickness and help the applicator maintain the
specified application rate.
Q7. What is the principal purpose of measuring surface profile after abrasive
blast cleaning?
A. To determine steel hardness
B. To determine the coating colour
C. To verify that the surface roughness is suitable for the specified coating
, system
D. To determine the ambient air temperature
Answer: C. To verify that the surface roughness is suitable for the specified
coating system
Rationale: Surface profile affects coating adhesion and the amount of
coating required to cover the peaks and valleys. The profile must therefore
comply with the coating specification.
Q8. Which method is commonly used to assess surface profile on blast-
cleaned steel?
A. Replica tape
B. Holiday detector
C. Wet film comb
D. Paint brush
Answer: A. Replica tape
Rationale: Replica tape can reproduce the surface profile and allow the
inspector to measure the resulting replica using an appropriate
micrometer.
Q9. What is the purpose of abrasive blast cleaning?
A. To apply the finish coat
B. To remove contaminants and produce an appropriate surface condition
and profile
C. To increase coating viscosity
D. To cure the coating
